Manualsbrain.com
  1. Handbücher
  2. Marken
  3. KitchenAid
  4. kgcu484vss
  5. Dimensionale Illustrationen

KitchenAid kgcu484vss Dimensionale Illustrationen

Download
Seite von 2
Because Whirlpool Corporation includes a continuous commitment to improve our 
products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation 
Instructions packed with product. Specifications subject to change without notice.
PRODUCT MODEL NUMBERS
Page 1 of 2
Ref. W10899357A
09/26/2016
KGCU483V
KGCU484V
KGCU467V
KGCU482V
KGCU407V
KGCU462V
KGCU463V
Commercial Style Gas Cooktop
PRODUCT DIMENSIONS
A.  30" (76.2 cm) cooktop: 29
7
/
8
" (75.9 cm)  
36" (91.4 cm) cooktop: 35
3
/
4
" (90.8 cm)  
48" (121.9 cm) cooktop: 47
7
/
8
" (121.6 cm)
B.  36" (91.4 cm) long 3 prong grounding-type power supply cord
C.  Model/serial/rating plate (located  
on the underside of the cooktop  
burner base)
D.  Island trim or optional backguard
E. 27
3
/
4
" (70.5 cm)
Side View of Cooktop
A. 27
3
/
4
" (70.5 cm)
B. 1
1
/
4
" (3.2 cm)
C. 7
7
/
16
" (18.8 cm)
D.  Gas inlet is located 1
7
/
8
" (4.8 cm) 
from the back of the cooktop 
burner base and 4
7
/
8
" (12.4 cm) in 
from left-hand side of the cooktop 
burner base.
E.  22" (55.9 cm)
F. 3
5
/
8
" (9.2 cm)
G. 1" (2.6 cm)
B
C
A
D
E
A
C
F
G
D
E
B
ELECTRICAL REQUIREMENTS
A 120-volt, 60 Hz, AC-only, 15-amp, fused electrical circuit 
is required. A time-delay fuse or circuit breaker is also 
recommended. It is recommended that a separate circuit 
serving only this cooktop be provided.
GAS REQUIREMENTS
Type of Gas
Natural Gas:
This cooktop is factory-set for use with Natural gas. To convert 
to LP gas, see the Gas Conversion instructions provided in the 
package containing literature. The model/serial/rating plate 
located on the left underside of the cooktop burner base has 
information on the types of gas that can be used. If the types of 
gas listed do not include the type of gas available, check with 
the local gas supplier.
LP Gas conversion:
Conversion must be done by a qualified service technician.
No attempt shall be made to convert the cooktop from the gas 
specified on the model/serial/rating plate for use with a different 
gas without consulting the serving gas supplier. To convert to LP 
gas, use the LP gas conversion kit provided with the cooktop 
and see the “Gas Conversions” section.
Gas Supply Line
 
■
Provide a gas supply line of 
3
/
4
" (1.9 cm) rigid pipe to the 
cooktop location. A smaller size pipe on longer runs may 
result in insufficient gas supply. With LP gas, piping or tubing 
size can be 
1
/
2
" (1.3 cm) minimum. Usually, LP gas suppliers 
determine the size and materials used in the system.
NOTE: Pipe-joint compounds that resist the action of LP gas 
must be used. Do not use TEFLON
®†
 tape.
†
®
TEFLON is a registered trademark of Chemours.
Flexible metal appliance connector:
 
■
If local codes permit, a new CSA design-certified, 4-5 ft 
(122-152.4 cm) long, 
5
/
8
" (1.6 cm) or 
3
/
4
" (1.9 cm) I.D. (inside 
diameter), flexible metal appliance connector may be used for 
connecting the cooktop to the gas supply line.
 
■
A 
1
/
2
" (1.3 cm) male pipe thread is needed for connection 
to the female pipe threads of the inlet to the appliance 
pressure regulator.
 
■
Do not kink or damage the flexible metal tubing when 
moving the cooktop.
 
■
Must include a shut-off valve: 
The supply line must be equipped with a manual shut-off 
valve. This valve should be located in the same room but 
external to the cooktop enclosure or cabinet. It should be in 
a location that allows ease of opening and closing. Do not 
block access to shut-off valve. The valve is for turning on or 
shutting off gas to the cooktop.
A.  Gas supply line
B.  Shut-off valve “open” 
position
C.  To cooktop
A
B
C