KitchenAid Gold® 30-inch Vented 300-CFM Under-Cabinet Hood Benutzung Und Pflege

®†TORX is a registered trademark of Acument Intellectual Properties, LLC

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

■

Drill

■

1¼" (3.0 cm) drill bit

■

⁄

" (3.0 mm) drill bit for pilot holes

■

Pencil

■

Wire stripper or utility knife

■

Tape measure or ruler

■

Caulking gun and weatherproof caulking compound

■

Flat-blade screwdriver

■

Phillips screwdriver

■

Saber or keyhole saw

■

Vent clamps

■

Metal snips

■

Compass or 8" (20.3 cm) circle template

Parts supplied

Remove parts from package. Check that all parts are included.

■

2 - Metal filters

■

6 - 3.5 x 9.5 mm mounting screws

■

3 - 4.5 x 13 mm damper screws

■

3¼" x 10" (8.3 x 25.4 cm) damper/vent connector

■

T-20 Torx®† adapter

Parts needed

■

3¼" x 10" (8.3 x 25.4 cm) or 6" (15.2 cm) or larger round metal

venting

■

6" (15.2 cm) or larger round damper, if using 6" (15.2 cm) or

larger round vent system

■

3¼" x 10" (8.3 x 25.4 cm) to 6" (15.2 cm) or larger diameter

transition piece if using 6" (15.2 cm) or larger diameter round

vent system.

■

3 - UL listed wire connectors

For cabinets with recessed bottoms:
■

Two 2" (5.1 cm) wide filler strips. Length and thickness

determined by recess dimensions.

■

Four flat head wood screws or machine screws with washers

and nuts (to attach filler strips).

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.
■

It is the installer’s responsibility to comply with installation

clearances specified on the model/serial rating plate. The

model/serial rating plate is located inside the range hood on

the left wall.

■

Range hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

■

Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance. Consult the

cooktop/range manufacturer installation instructions before

making any cutouts.

■

Grounded electrical outlet is required. See “Electrical

Requirements” section.

■

The hood is factory-set for vented installations.

■

All openings in ceiling and wall where range hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title

24 CFR, Part 328 (formerly the Federal Standard for Mobile

Home Construction and Safety, title 24, HUD, Part 280)

or when such standard is not applicable, the standard for

Manufactured Home Installation 1982 (Manufactured Home

Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or

latest edition, or with local codes.

Product Dimensions

29¹⁵⁄₁₆" (76.0 cm)

20"

(50.8 cm)

(22.9 cm)

1¹⁄₂"

(3.8 cm)

4³⁄₄"

(12.1 cm)

(2.5 cm)

4¹⁄₁₆" (10.3 cm)

1³⁄₄"

(4.4 cm)

³⁄₄

(2.0 cm)