PEHA Aura D 20.455.21 FU-BLS N Benutzerhandbuch
Produktcode
D 20.455.21 FU-BLS N
Easyclick radio system
Easyclick flush-mounted series receiver
4-channel switching module, for mounting on DIN rail, with two pushbuttons,
454 FU-E REG
380213
each with ON/OFF function.
30 Easyclick transmitters can be trained to work with one receiver.
Connection options: 2 push-to-make switches and 2 changeover contact (zero-potential
and independently programmable), dimensions: 72 mm wide (4 module widths),
Aerial 460 ANT is needed.
Supply voltage 230 V, 50 Hz, neutral conductor required, screw terminals,
the contacts must not be operated with mixed voltages (i.e. safety extra-low voltage
and 230 V).
Connection data for electrically powered units
per channel:
30 Easyclick transmitters can be trained to work with one receiver.
Connection options: 2 push-to-make switches and 2 changeover contact (zero-potential
and independently programmable), dimensions: 72 mm wide (4 module widths),
Aerial 460 ANT is needed.
Supply voltage 230 V, 50 Hz, neutral conductor required, screw terminals,
the contacts must not be operated with mixed voltages (i.e. safety extra-low voltage
and 230 V).
Connection data for electrically powered units
per channel:
push-to-make (PTM) push-to-break (PTB)
Filament lamp (ohmic load)
2500 W
1000 W
High-voltage halogen lamps
1250 W
500 W
Inductive load
600 VA
250 W
Electronic ballast
3 pieces
1 piece
Aerial for flush-mounted series receiver
External aerial with magnetic base. Improves the reception of
460 ANT
378213
Easyclick flush-mounted series receivers and the Easyclick interface.
Easyclick PHC/PHC Compact interface
The Easyclick PHC/PHC-Compact interface permits connection between the
940 FU C
262217
Easyclick radio transmitters and the PHC or PHC-Compact system,
this includes connection cable 30 cm, 72 mm wide (4 module widths).
The Easyclick PHC/PHC-Compact interface has 32 inputs for Easyclick transmitters and
it converts the radio signals from these into input signals for the PHC or PHC-Compact
system. The electrically powered units are driven via output, shutter, and dimmer
modules. Up to a total of 240 transmitters for ON/OFF can be trained.
The Easyclick PHC/PHC-Compact interface 940 FU C must be programmed using the
PHC software, version 2.4 and above.
Technical data:
Power supply:
this includes connection cable 30 cm, 72 mm wide (4 module widths).
The Easyclick PHC/PHC-Compact interface has 32 inputs for Easyclick transmitters and
it converts the radio signals from these into input signals for the PHC or PHC-Compact
system. The electrically powered units are driven via output, shutter, and dimmer
modules. Up to a total of 240 transmitters for ON/OFF can be trained.
The Easyclick PHC/PHC-Compact interface 940 FU C must be programmed using the
PHC software, version 2.4 and above.
Technical data:
Power supply:
24V DC via the PHC bus
Internal consumption:
approx. 30 to 40 mA
Operating controls:
2 pushbuttons “Program” and “Clear”
Display elements:
1 LED for receive
3 x 7 segment display for channel setting
3 x 7 segment display for channel setting
Transmission frequency: 868,3 MHz
Connections:
Connections:
2 modular sockets for the PHC bus
1 aerial socket for an external aerial
(Antenna 460 ANT is needed)
1 aerial socket for an external aerial
(Antenna 460 ANT is needed)
Easyclick PHC interface
The Easyclick-PHC interface permits bidirectional connection between the Easyclick radio
941 FU C
262717
transmitters and receivers and the PHC system, this includes connecting cable 30 cm,
72 mm wide (4 module widths).
The Easyclick PHC interface has 120 inputs for Easyclick transmitters; it converts the radio
signals from these into input signals for the PHC system. Up to a total of 240 individual
transmitter channels (pushbuttons etc.) distributed over any number of inputs can be trained.
The Easyclick PHC interface also has 120 outputs for Easyclick switching receivers,
shutters/blinds receivers, and dimmer receivers. The Easyclick PHC interface 941 FU-C
must be programmed using the PHC software, version 2.8 and above (German version)
Technical data:
Power supply:
72 mm wide (4 module widths).
The Easyclick PHC interface has 120 inputs for Easyclick transmitters; it converts the radio
signals from these into input signals for the PHC system. Up to a total of 240 individual
transmitter channels (pushbuttons etc.) distributed over any number of inputs can be trained.
The Easyclick PHC interface also has 120 outputs for Easyclick switching receivers,
shutters/blinds receivers, and dimmer receivers. The Easyclick PHC interface 941 FU-C
must be programmed using the PHC software, version 2.8 and above (German version)
Technical data:
Power supply:
24 V DC via the PHC bus
Internal consumption:
30 to 40 mA
Operating controls:
2 pushbuttons “Program” and “Send/Clear”
Display elements:
2 LEDs, send (red) and receive (green)
3 x 7 segment display for channel setting
3 x 7 segment display for channel setting
Transmission frequency: 868,3 MHz
Terminals:
Terminals:
2 modular sockets for the PHC bus
1 aerial socket for an external aerial
(460 ANT is needed)
1 aerial socket for an external aerial
(460 ANT is needed)
Easyclick diagnostic tool
for checking the strength of Easyclick radio signals and for determining
450 TEST
386513
the best positions for transmitters and receivers .
Dimensions: 150 x 50 x 22 mm (L x W x H),
battery: 9-volt block (not included in delivery).
Dimensions: 150 x 50 x 22 mm (L x W x H),
battery: 9-volt block (not included in delivery).
Article designation
Colour
Article No.
Code No.