Intel L5630 AT80614005484AA Benutzerhandbuch
Produktcode
AT80614005484AA
Features
162
Intel
®
Xeon
®
Processor 5600 Series Datasheet Volume 1
Power-On Configuration (POC) logic levels are MUX’ed onto the VID[7:0] signals with
1-5 kΩ pull-up and pull-down resistors located on the baseboard. These include:
1-5 kΩ pull-up and pull-down resistors located on the baseboard. These include:
• VID[2:0] / MSID[2:0] = Market Segment ID
• VID[5:3] / CSC [2:0] = Current Sense Configuration
• VID[6] = Reserved
• VID[7] = VR11.1 Select
• VID[5:3] / CSC [2:0] = Current Sense Configuration
• VID[6] = Reserved
• VID[7] = VR11.1 Select
Pull-up and pull-down resistors on the baseboard eliminate the need for timing
specifications. After OUTEN signal is asserted, the VID[7:0] CMOS drivers (typically 50
Ω up/down impedance) over-ride the POC pull-up/down resistors located on the
specifications. After OUTEN signal is asserted, the VID[7:0] CMOS drivers (typically 50
Ω up/down impedance) over-ride the POC pull-up/down resistors located on the
baseboard and drive the necessary VID pattern. Please refer to
for further
details.
8.2
Clock Control and Low Power States
The processor supports low power states at the individual thread, core, and package
level for optimal power management. The processor implements software interfaces for
requesting low power states: MWAIT instruction extensions with sub-state hints, the
HLT instruction (for C1 and C1E) and P_LVLx reads to the ACPI P_BLK register block
mapped in the processor’s I/O address space. The P_LVLx I/O reads are converted to
equivalent MWAIT C-state requests inside the processor and do not directly result in
I/O reads to the system. The P_LVLx I/O Monitor address does not need to be set up
before using the P_LVLx I/O read interface.
level for optimal power management. The processor implements software interfaces for
requesting low power states: MWAIT instruction extensions with sub-state hints, the
HLT instruction (for C1 and C1E) and P_LVLx reads to the ACPI P_BLK register block
mapped in the processor’s I/O address space. The P_LVLx I/O reads are converted to
equivalent MWAIT C-state requests inside the processor and do not directly result in
I/O reads to the system. The P_LVLx I/O Monitor address does not need to be set up
before using the P_LVLx I/O read interface.
Note:
Software may make C-state requests by using a legacy method involving I/O reads
from the ACPI-defined processor clock control registers, referred to as P_LVLx. This
feature is designed to provide legacy support for operating systems that initiate C-state
transitions via access to pre-defined ICH registers. The base P_LVLx register is P_LVL2,
corresponding to a C3 request. P_LVL3 is C6, and all P_LVL4+ are demoted to a C6.
from the ACPI-defined processor clock control registers, referred to as P_LVLx. This
feature is designed to provide legacy support for operating systems that initiate C-state
transitions via access to pre-defined ICH registers. The base P_LVLx register is P_LVL2,
corresponding to a C3 request. P_LVL3 is C6, and all P_LVL4+ are demoted to a C6.
P_LVLx is limited to a subset of C-states (For example, P_LVL8 is not supported and will
not cause an I/O redirection to a C8 request. Instead, it will fall through like a normal
I/O instruction). The range of I/O addresses that may be converted into C-state
requests is also defined in the PMG_IO_CAPTURE MSR, in the ‘C-state Range’ field. This
field maybe written by BIOS to restrict the range of I/O addresses that are trapped and
redirected to MWAIT instructions. Note that when I/O instructions are used, no MWAIT
substates can be defined, as therefore the request defaults to have a sub-state or zero,
but always assumes the ‘Break on EFLAGS.IF==0’ control that can be selected using
ECX with an MWAIT instruction.
not cause an I/O redirection to a C8 request. Instead, it will fall through like a normal
I/O instruction). The range of I/O addresses that may be converted into C-state
requests is also defined in the PMG_IO_CAPTURE MSR, in the ‘C-state Range’ field. This
field maybe written by BIOS to restrict the range of I/O addresses that are trapped and
redirected to MWAIT instructions. Note that when I/O instructions are used, no MWAIT
substates can be defined, as therefore the request defaults to have a sub-state or zero,
but always assumes the ‘Break on EFLAGS.IF==0’ control that can be selected using
ECX with an MWAIT instruction.