Honeywell Honeywell Security | Protect What Matters Most Betriebsanweisung
– 26 –
Macro Key Programming & Usage
Macro Key Programming & Usage
Macro Key Programming & Usage
Macro Key Programming & Usage
(cont.)
(cont.)
(cont.)
(cont.)
The keypad beeps to acknowledge your input and
displays the command you entered (followed by “F”).
displays the command you entered (followed by “F”).
3. Enter the next command, followed by press/holding
the “D” key for at least two seconds. The keypad
beeps and displays the keystrokes entered so far.
beeps and displays the keystrokes entered so far.
4. Repeat until all the desired commands (up to 16
characters including the “F”s) have been entered.
Be sure to check your keystrokes before continuing.
If you made a mistake, you must start over.
If you made a mistake, you must start over.
5. To exit, press/hold the “D” key for at least two
seconds. The display returns to system status and
indicates system is ready.
indicates system is ready.
Typical Macro Alpha Display:
MACRO PGM
6 0 2 F 0 3 F
#
7 0 1 F 2 F
Example of Macro Programming
Example of Macro Programming
Example of Macro Programming
Example of Macro Programming
Suppose you want to (1) bypass the two upstairs window zones, then (2) turn on an
exterior light, and then (3) arm the security system in the AWAY mode. The
procedures in the table that follows show you how you would program this macro:
exterior light, and then (3) arm the security system in the AWAY mode. The
procedures in the table that follows show you how you would program this macro:
Function
Keystrokes Required
Keypad Display
1. Bypass zones 02 &
03
03
Press BYPASS [6] key, then
2-digit zone number 02, then
terminator “D”’ then [6], then 2-digit
zone number 03, then terminator “D”.
2-digit zone number 02, then
terminator “D”’ then [6], then 2-digit
zone number 03, then terminator “D”.
6 0 2 F 6 0 3
2. Insert terminator.
Press the “D” key for at least 2 seconds.
6 0 2 F 6 0 3 F
3. Turn light on
(device 01).
(device 01).
Press [#] and 7 keys for “device ON”,
and [01] key for selecting device 1.
and [01] key for selecting device 1.
6 0 2 F 6 0 3 F
#
7 0 1 F
4. Insert terminator.
Press the “D” key for at least 2 seconds.
6 0 2 F 6 0 3 F
#
7 0 1 F
5. Arm system AWAY Press
AWAY [2] key.
6 0 2 F 6 0 3 F
#
7 0 1 F 2
6. Insert terminator.
Press the “D” key for at least 2 seconds.
6 0 2 F 6 0 3 F
#
7 0 1 F 2 F
7. Exit Macro mode
Press the “D” key again.
Using a Programmed Macro Key
Using a Programmed Macro Key
Using a Programmed Macro Key
Using a Programmed Macro Key
DISARMED
READY TO ARM
READY TO ARM
1. Press the Macro key programmed for the desired
series of commands for at least 2 seconds. The “Enter
User Code” prompt appears. The prompt remains
displayed for up to 30 seconds.
User Code” prompt appears. The prompt remains
displayed for up to 30 seconds.
ENTER USER CODE
* * * *
* * * *
2.
Enter your 4-digit security code.
The programmed macro sequence begins
automatically after the user code is entered.
automatically after the user code is entered.