Kraft KF-SL 60802 MWB Benutzerhandbuch

P.08

P.09

3.Ensure the positioning status of washing machine. Loosen the lock nut with spanner

   and turn the leg with hand until it closely contacts with the floor. Press the leg with one 

   hand and fasten the nut closely to the cabinet with the other hand.

4.After being locked properly, press four corners again to make sure that they has been 

   adjusted properly. If it is still unstable, it has to repeat Steps 2 and 3.

 

    

   

      Connect inlet pipe

Connect the inlet pipe as indicated in the figure.

For the model which has hot valve , please connect 

the hot vale to hot water tap. Energy will decrease 

automatically for some program.

   

      Install inlet pipe

1.Connect the elbow to tap and fasten it 

   clockwise.

2.Connect the other end of inlet pipe to the inlet 

   valve at the backside of washing machine and 

   fasten the pipe tightly clockwise.

Notes: after connection, if there is any leakage 

with hose, then repeat the steps to connect inlet

pipe. The most common type of tap shall be 

used to supply water. If tap is square or too big, 

then standard tap shall be changed.

      Place outlet hose

There are two ways to place the end of outlet hose:

1.Put it beside the water trough.

 

   

Unpack your washing machine and check if there is any damage during the transportation. 

Also make sure that all the items (as shown in Page 5) in the attached bag are received. 

If there is any damage to the washing machine during the transportation, or any item is 

missing, please contact the local dealer immediately.
    

The packing materials of this machine may be dangerous to kids. Please dispose them 

properly and avoid easy touch by kids. Please dispose the related packing materials 

according to the relevant local regulations. Please do no throw the packing materials 

away together with the other daily living rubbishes. 
    

Before using this washing machine, transport bolts 

must be removed from the backside of

this machine. Please take the following steps to 

remove the bolts:

1.Loosen all bolts with spanner and then remove them.

2.Stop the holes with transport hole plugs.

3.Keep the transport bolts properly for future use.
    

Before installing the washing machine, the location characterized as follows shall be

selected:

-   Rigid, dry, and level surface (if not level, please make it level with reference to the

    following figure “Adjust Leg”)

-   Avoid direct sunlight

-   Sufficient ventilation

-   Room temperature is above 0 C 

-   Keep far away from the heat resources such as coal or gas.

Make sure that the washing machine will not stand on power cord.

Do not install the washing machine on the carpet floor.
     

1.When positioning the washing machine, please 

   first check if the legs are closely attached to the 

   cabinet. If not, please turn them to their original 

   positions with hand or spanner and tighten the 

   nuts with spanner.

2.After positioning the washing machine, press 

   four corners on top cover of washing machine 

   in sequence. If the washing machine is not 

   stable when being pressed, this leg shall be 

   adjusted.

5.Put a solid cylinder (e.g. pop cans) oppositely on the top cover of the washing machine from in 
the left, right, front and back directions. If the cylinder keeps stable, the washing machine is
 positioned level. If it rolls, the washing machineis positioned unlevel. The rolling direction is the 
direction of lower ground surface.Then, the two legs in this direction shall be raised at the same time
 until the washing machine is level. Steps 1~3 are repeated to make the bottom legs closely against 
the ground and the nuts shall be locked tightly.      

P.10

P.11

2.Connect it to the branch drain pipe of the trough.

-    As the maximum current through the unit is 10A when you are using its heating function,

     please make sure the power supply system (current, power voltage and wire) at your 

     home can meet the normal loading requirements of the electrical appliances.

-    Please connect the power to a socket which is correctly installed and properly earthed.

-    Make sure the power voltage at your place is same to that in the machine's rating label. 

-    Power plug must match the socket and cabinet must be properly and effectively earthed.

-    Do not use multi-purpose plug or socket as extension cord.

-    Do not connect and pull out plug with wet hand.

-    When connecting and pulling out the plug, hold the plug tightly and then pull it out. Do 

     not pull power cord forcibly.

-    If power cord is damaged or has any sign of being broken, special power cord must be 

     selected or purchased from its manufacturer or service center for replacement.

 

1.This machine must be earthed properly. If there is any short circuit, earthing can reduce 

   the danger of electrical shock.

This machine is equipped with power cord, which includes plug, earthing wire at earthing 

terminal.

2.Washing machine shall be operated in a circuit separate from other electrical appliances. 

   Otherwise, power protector may be tripped or fuse may be burned out. 

     

Please read this operation method carefully to avoid the troubles of washing machine and 

damages of clothes.

After a white towel touched with liquid detergent is used to wash the invisible corners of the 

clothes, check if the white towel is stained with 

clothes' original color.

As for the scarves and those clothes that easily 

get decolorized among imported clothes, please 

wash them separately before washing.

As for the stains on sleeves, collars and pockets, 

use the liquid detergent and wash it with brush 

gently. Finally put them into the washing machine 

to achieve more ideal washing effects.

As for temperature-sensitive clothes, they shall 

be washed as required in the labels. Otherwise, 

it may cause color change or distortion.

Never put the clothes to be washed in washing machine for a long period of time. 

Otherwise it may get moldy and cause spots. Therefore, please wash the clothes in time. 

The clothes also may get color changed or distorted if they are not washed according to 

the stated washing temperature.

The clothes that may get distorted if being immersed in water:

Ties, waistcoats, western-style clothes, outer garments etc. may have obvious shrinkage

 if being immersed in water; the decolorized clothes such as blended spinning clothes of 

artificial fiber etc.

！

M

ax

.1

00

cm

M

in

.6

0c

m

M

in

.6

0c

m

M

ax

.1

00

cm

 Position outlet hose properly so that the floor will not be damaged by water leakage.

-   When installing outlet hose, fix it 

    properly with a rope. 

-   Position outlet hose properly so that 

    the floor will not be damaged by water

    leakage.

Trough

Hose Retainer

Bind

Max.100cm

Min.60cm

M

in

.6

0c

m

M

ax

.1

00

cm

-   If outlet hose is too long, do not force 

    it into washing machine as it will cause 

    abnormal noises.

 Notes: 

 If the machine has outlet hose support, please install it like the following pictures.