Cisco Cisco Packet Data Gateway (PDG) Installationsanleitung
ASR 5000 Hardware Platform Overview
▀ Line Cards
▄ ASR 5000 Installation Guide
48
Channelized Line Card (CLC2)
The CLC2 is also referred to as the Frame Relay line card. It provides frame relay over SONET or SDH. The CLC2
supports network connectivity through a gigabit interface to connect to the Packet Control Unit (PCU) of the base
station subsystem (BSS) in a mobile network. These interfaces are commonly used with the SGSN product to support
frame relay.
supports network connectivity through a gigabit interface to connect to the Packet Control Unit (PCU) of the base
station subsystem (BSS) in a mobile network. These interfaces are commonly used with the SGSN product to support
frame relay.
In North America, the card supplies ANSI SONET STS-3 (optical OC-3) signaling. In Europe, the card supplies SDH
STM-1 (optical OC-3). The transmission rate for the card is 155.52 Mbps with 336 SONET channels for T1 and 252
SDH channels for E1.
STM-1 (optical OC-3). The transmission rate for the card is 155.52 Mbps with 336 SONET channels for T1 and 252
SDH channels for E1.
Each CLC2 provides four optical fiber physical interfaces (ports). The ports are populated by a Small Form-factor
Pluggable (SFP) modules which include an LC-type connector. The ports of the CLC2 supports two types of SFP
modules and cabling, as shown in the following table.
Pluggable (SFP) modules which include an LC-type connector. The ports of the CLC2 supports two types of SFP
modules and cabling, as shown in the following table.
Table 20.
SFP Modules supported by the CLC2
Module Type
Card Identification
Interface Type
Cable Specifications
Single-mode
Optical Fiber
Optical Fiber
Channelized (STM-1/OC-3)
SM IR-1
SM IR-1
Single-mode Fiber, LC
duplex female connector
duplex female connector
Fiber Types: Single-mode optical fiber
Wavelength: 1310 nm
Core Size: 9 micrometers
Cladding Diameter: 125 micrometers
Range: Intermediate/21 kilometers
Attenuation: 0.25 dB/KM
Min/Max Tx Power: -15 dBm/-8 dBm
Rx Sensitivity: -28 dBm
Wavelength: 1310 nm
Core Size: 9 micrometers
Cladding Diameter: 125 micrometers
Range: Intermediate/21 kilometers
Attenuation: 0.25 dB/KM
Min/Max Tx Power: -15 dBm/-8 dBm
Rx Sensitivity: -28 dBm
Multi-mode
Optical Fiber
Optical Fiber
Channelized (STM-1/OC-3)
Multi-Mode
Multi-Mode
Multi-mode Fiber, LC
duplex female connector
duplex female connector
Fiber Types: Multi-mode optical fiber
Wavelength: 1310 nm
Core Size: 62.5 micrometers
Cladding Diameter: 125 micrometers
Range: Short/2 kilometers
Min/Max Tx Power: -19 dBm/-14 dBm
Rx Sensitivity: -30 dBm
Wavelength: 1310 nm
Core Size: 62.5 micrometers
Cladding Diameter: 125 micrometers
Range: Short/2 kilometers
Min/Max Tx Power: -19 dBm/-14 dBm
Rx Sensitivity: -30 dBm
The CLC2 supports the Star Channel (1 Gbps) for faster FPGA upgrades and is Restriction of Hazardous Substances
(RoHS) 6/6 compliant.
(RoHS) 6/6 compliant.
Install the CLC2 directly behind its respective (Active) packet processing card. You may optionally install CLC2s
behind a redundant (Standby) packet processing card. As with other line cards, install the Channelized Line Cards in
slots 17 through 23, 26 through 39, and 42 through 48.
behind a redundant (Standby) packet processing card. As with other line cards, install the Channelized Line Cards in
slots 17 through 23, 26 through 39, and 42 through 48.
The following figures show the panel of the CLC2 Channelized Line Cards, identifying their interfaces and major
components.
components.