Cisco Cisco Packet Data Gateway (PDG)
Configuring the Evolved Packet Data Gateway
Configuring the System to Perform as an Evolved Packet Data Gateway ▀
ePDG Administration Guide, StarOS Release 18 ▄
105
route
command configures a static IPv6 route to the next-hop router. In this configuration, it configures a static route
from the ePDG to the P-GW over the S2b interface. The
bind interface
command binds each logical interface to a
physical Ethernet port.
Bulk Statistics Configuration
Use the following configuration example to enable ePDG bulk statistics:
configure
bulkstats collection
bulkstats mode
sample-interval <time_interval>
transfer-interval <xmit_time_interval>
file <number>
receiver <ip_address> primary mechanism ftp login <username> password <pwd>
receiver <ip_address> secondary mechanism ftp login <username> password <pwd>
epdg schema <file_name> format " txbytes : %txbytes% txpkts : %txpkts% rxbytes :
%rxbytes% rxpkts : %rxpkts sess-txbytes : %sess-txbytes% sess-rxbytes : %sess-rxbytes%
sess-txpackets : %sess-txpackets% sess-rxpackets : %sess-rxpackets eap-rxttlsrvrpassthru
: %eap-rxttlsrvrpassthru% eap-rxsuccsrvrpassthru : %eap-rxsuccsrvrpassthru% num-gtp-
bearermodified : %num-gtp-bearermodified% num-gtp-db-active : %num-gtp-db-active% num-
gtp-db-released : %num-gtp-db-released% curses-gtp-ipv4 : %curses-gtp-ipv4% curses-gtp-
ipv6 : %curses-gtp-ipv6% curses-gtp-ipv4v6 : %curses-gtp-ipv4v6% "
%rxbytes% rxpkts : %rxpkts sess-txbytes : %sess-txbytes% sess-rxbytes : %sess-rxbytes%
sess-txpackets : %sess-txpackets% sess-rxpackets : %sess-rxpackets eap-rxttlsrvrpassthru
: %eap-rxttlsrvrpassthru% eap-rxsuccsrvrpassthru : %eap-rxsuccsrvrpassthru% num-gtp-
bearermodified : %num-gtp-bearermodified% num-gtp-db-active : %num-gtp-db-active% num-
gtp-db-released : %num-gtp-db-released% curses-gtp-ipv4 : %curses-gtp-ipv4% curses-gtp-
ipv6 : %curses-gtp-ipv6% curses-gtp-ipv4v6 : %curses-gtp-ipv4v6% "
end
The
bulkstats collection
command in this example enables bulk statistics, and the system begins collecting pre-
defined bulk statistical information.
The
bulkstats mode
command enters Bulk Statistics Configuration Mode, where you define the statistics to collect.
The
sample-interval
command specifies the time interval, in minutes, to collect the defined statistics. The <
time-
interval
> can be in the range of 1 to 1440 minutes. The default value is 15 minutes.
The
transfer-interval
command specifies the time interval, in minutes, to transfer the collected statistics to the
receiver (the collection server). The <
xmit_time_interval
> can be in the range of 1 to 999999 minutes. The default
value is 480 minutes.
The
file
command specifies a file in which to collect the bulk statistics. A bulk statistics file is used to group bulk
statistics schema, delivery options, and receiver configuration. The <
number
> can be in the range of 1 to 4.
The
receiver
command in this example specifies a primary and secondary collection server, the transfer mechanism
(in this example, ftp), and a login name and password.
The
epdg schema
command specifies that the epdg schema is used to gather statistics. The <
file_name
> is an
arbitrary name (in the range of 1 to 31 characters) to use as a label for the collected statistics defined by the
format
option. The
format
option defines within quotation marks the list of variables in the epdg schema to collect. The
format string can be in the range of 1 to 3599.