Cisco Cisco Packet Data Gateway (PDG) Ratgeber Für Administratoren
Troubleshooting
▀ Detecting Faulty Hardware
▄ Cisco ASR 5500 System Administration Guide
180
Table 22. DPC/UDPC Active LED States
Color
Description
Troubleshooting
Green
Card is active.
The first time power is applied to the system, all of the DPC/UDPCs should be
booted into the standby mode. Therefore, this LED should be off.
booted into the standby mode. Therefore, this LED should be off.
Blinking
Green
Green
Tasks or processes are being
migrated from an active DPC
to a standby DPC.
migrated from an active DPC
to a standby DPC.
Verify that the Redundancy LED on a standby DPC/UDPC is also blinking green. If
so, there is an issue with the active DPC/UDPC and it is transferring its processes.
so, there is an issue with the active DPC/UDPC and it is transferring its processes.
Refer to Monitoring the System for information on determining the status of the
DPC/UDPC and system software processes and functionality.
DPC/UDPC and system software processes and functionality.
None
Card is not receiving power.
OR
Card is in Standby Mode.
OR
Card is in Standby Mode.
Verify that the Run/Fail LED is green. If so, the card is receiving power and POST
test results are positive. If it is off, refer to
test results are positive. If it is off, refer to
for
troubleshooting information.
Check the state of the Redundancy LED. If it is green, the card is in standby mode.
This is normal operation for the initial power-up. If needed, refer to the Configuring
DPC Availability section of System Settings for information on making the card
active.
This is normal operation for the initial power-up. If needed, refer to the Configuring
DPC Availability section of System Settings for information on making the card
active.
DPC/UDPC Redundancy LED States
The Redundancy LED on the DPC/UDPC indicates that software is loaded on the card, but it is serving as a standby
component. DPC/UDPCs support n:1 redundancy; the Redundancy LED should be green on only one DPC/UDPC for
normal system operation.
component. DPC/UDPCs support n:1 redundancy; the Redundancy LED should be green on only one DPC/UDPC for
normal system operation.
The possible states for this LED are described in the following table. If the LED is not green, use the troubleshooting
information in the table to diagnose the problem.
information in the table to diagnose the problem.
Table 23. DPC/UDPC Redundancy LED States
Color
Description
Troubleshooting
Green
Card is in standby mode.
None needed. There is at least one DPC/UDPC in Standby mode.
Amber
Card is not backed up by a
standby DPC.
standby DPC.
Check the status of the other DPC/UDPCs. If one DPC/UDPC has failed or has
been removed from the chassis, the system can continue to function but
redundancy is compromised.
been removed from the chassis, the system can continue to function but
redundancy is compromised.
Refer to Monitoring the System for information on determining the status of the
DPC/UDPC and system software processes.
DPC/UDPC and system software processes.
Blinking
Amber
Amber
Tasks or processes being migrated
from an active DPC to the
standby DPC.
from an active DPC to the
standby DPC.
Refer to Monitoring the System for information on determining the status of the
DPC/UDPC and system software processes.
DPC/UDPC and system software processes.
None
Card is not receiving power.
OR
Card has failed.
OR
Card has failed.
Verify that the Run/Fail LED is green. If so, the card is receiving power and
POST test results are positive. If it is off, refer to
POST test results are positive. If it is off, refer to
for troubleshooting information.