Cisco Cisco Prime Optical 10.3 Entwickleranleitung
Cisco Prime Optical 10.3 GateWay/CORBA Programmer Reference Guide
217
• EnableSyncMsg
• TraceMode
The SDH_SONET_SS_BITS parameter can be modified only when EnableSyncMsg is Off.
EnableSyncMsg can be set to On only if SDH_SONET_SS_BITS is set to SONET.
The SDH_SONET_SS_BITS and EnableSyncMsg parameters must be modified by invoking two
separate method calls. If you try to use the same method to modify SDH_SONET_SS_BITS and
EnableSyncMsg, Prime Optical generates a processing failure exception.
The TraceMode parameter can be modified. The DisableFDIonTTIM parameter is disabled when
TraceMode is set to MANUAL and enabled when TraceMode is MANUALNOAIS.
The setTPData interface does not apply to the following ML-series card parameters that are
configurable through Cisco IOS:
• Admin state, MTU size, and COS accounting for POS and Ethernet interfaces.
• Speed, duplex, and flow control for Ethernet interfaces.
Prime Optical supports the following automatic laser shutdown parameters on PTPs. These
parameters are not defined by the TMF.
• ALSMode
• PulseWidth
• RecoveryInterval
• RestartLaser
If the equipment is the protecting equipment in a 1_For_N protection group, Prime Optical sets
the PTPs on the equipment to AlarmReporting.
Prime Optical supports only the following parameters for FTPs:
• TrailTraceExpectedRx
• TrailTraceMonitor
For valid values for each parameter, see Table 3-4 in
• TraceMode
The SDH_SONET_SS_BITS parameter can be modified only when EnableSyncMsg is Off.
EnableSyncMsg can be set to On only if SDH_SONET_SS_BITS is set to SONET.
The SDH_SONET_SS_BITS and EnableSyncMsg parameters must be modified by invoking two
separate method calls. If you try to use the same method to modify SDH_SONET_SS_BITS and
EnableSyncMsg, Prime Optical generates a processing failure exception.
The TraceMode parameter can be modified. The DisableFDIonTTIM parameter is disabled when
TraceMode is set to MANUAL and enabled when TraceMode is MANUALNOAIS.
The setTPData interface does not apply to the following ML-series card parameters that are
configurable through Cisco IOS:
• Admin state, MTU size, and COS accounting for POS and Ethernet interfaces.
• Speed, duplex, and flow control for Ethernet interfaces.
Prime Optical supports the following automatic laser shutdown parameters on PTPs. These
parameters are not defined by the TMF.
• ALSMode
• PulseWidth
• RecoveryInterval
• RestartLaser
If the equipment is the protecting equipment in a 1_For_N protection group, Prime Optical sets
the PTPs on the equipment to AlarmReporting.
Prime Optical supports only the following parameters for FTPs:
• TrailTraceExpectedRx
• TrailTraceMonitor
For valid values for each parameter, see Table 3-4 in
For PTPs, the layeredParameters and additionalInfo attribute lists contain the OTU1 and OTU2
attribute values if the selected card is one of the following:
• AR-XP (ONS15454 SONET and ONS15454 SDH, ONS NCS2K SONET, and ONS NCS2K
attribute values if the selected card is one of the following:
• AR-XP (ONS15454 SONET and ONS15454 SDH, ONS NCS2K SONET, and ONS NCS2K
SDH)
• AR-MXP (ONS15454 SONET and ONS15454 SDH, ONS NCS2K SONET, and ONS
NCS2K SDH)
For PTPs, the additionalInfo attribute list contains the OTU2 protection regeneration attribute
value if the selected card is one of the following:
• AR-XP (ONS15454 SONET and ONS15454 SDH, ONS NCS2K SONET, and ONS NCS2K
value if the selected card is one of the following:
• AR-XP (ONS15454 SONET and ONS15454 SDH, ONS NCS2K SONET, and ONS NCS2K
SDH)
• AR-MXP (ONS15454 SONET and ONS15454 SDH, ONS NCS2K SONET, and ONS
NCS2K SDH)
For PTPs, the additionalInfo attribute list contains the AUTO attribute value if the selected card
is one of the following:
• AR-XP (ONS15454 SONET and ONS15454 SDH, ONS NCS2K SONET, and ONS NCS2K
is one of the following:
• AR-XP (ONS15454 SONET and ONS15454 SDH, ONS NCS2K SONET, and ONS NCS2K
SDH)
• AR-MXP (ONS15454 SONET and ONS15454 SDH, ONS NCS2K SONET, and ONS
NCS2K SDH)
For more information on AR-XP and AR-MXP cards, see