Cisco Cisco Prime Network Services Controller Adaptor for DFA Merkblatt
Purpose
Command or Action
Sends additional paths to and from the BGP peers.
switch (config-router-af) # additional-paths send
Step 13
Receives additional paths to and from the BGP peers.
switch (config-router-af) # additional-paths receive
Step 14
Specifies the route map for the additional paths selection.
switch (config-router-af) # additional-paths
selection route-map
selection route-map
Step 15
Enters address family mode and configures submode
commands for the BGP.
commands for the BGP.
switch (config-router) # address-family vpnv6
unicast
unicast
Step 16
Sends additional paths to and from the BGP peers.
switch (config-router-af) # additional-paths send
Step 17
Receives additional paths to and from the BGP peers
switch (config-router-af) # additional-paths receive
Step 18
Specifies the route map for the additional paths selection.
switch (config-router-af) # additional-paths
selection route-map
selection route-map
Step 19
Configures a BGP neighbor (router, vrf) and enters neighbor
configuration mode.
configuration mode.
switch (config-router) # neighbor
{bgp-client-subnet/mask} [remote-as {as-num
[,as-num]}
{bgp-client-subnet/mask} [remote-as {as-num
[,as-num]}
Step 20
Enters address family mode or a virtual routing and
forwarding (VRF) address-family mode to configure submode
commands for the BGP.
forwarding (VRF) address-family mode to configure submode
commands for the BGP.
switch (config-router-neighbor) # address-family
ipv4 unicast
ipv4 unicast
Step 21
Sends a BGP community attribute to a peer.
switch (config-router-neighbor-af) #
send-community
send-community
Step 22
Sends a BGP community attribute to a peer.
switch (config-router-neighbor-af) #
send-community [extended]
send-community [extended]
Step 23
Configures the router as a BGP route reflector and configures
the specified neighbor as its client.
the specified neighbor as its client.
switch (config-router-neighbor-af)
#route-reflector-client
#route-reflector-client
Step 24
Enters address family mode configure submode commands
for the BGP.
for the BGP.
switch (config-router-neighbor) # address-family
ipv6 unicast
ipv6 unicast
Step 25
Sends a BGP community attribute to a peer.
switch (config-router-neighbor-af) #
send-community [extended]
send-community [extended]
Step 26
Configures the router as a BGP route reflector and configures
the specified neighbor as its client.
the specified neighbor as its client.
switch (config-router-neighbor-af)
#route-reflector-client
#route-reflector-client
Step 27
Enters address family mode configure submode commands
for the BGP.
for the BGP.
switch (config-router-neighbor) # address-family
vpnv4 unicast
vpnv4 unicast
Step 28
Sends a BGP community attribute to a peer.
switch (config-router-neighbor-af) #
send-community [extended]
send-community [extended]
Step 29
Configures the router as a BGP route reflector and configures
the specified neighbor as its client.
the specified neighbor as its client.
switch (config-router-neighbor-af) #
route-reflector-client
route-reflector-client
Step 30
Configures BGP to advertise the capability of sending and
receiving additional paths to and from the BGP peers.
receiving additional paths to and from the BGP peers.
switch (config-router-neighbor-af) # capability
additional-paths receive
additional-paths receive
Step 31
Enters address family mode configure submode commands
for the BGP.
for the BGP.
switch (config-router-neighbor)
#address-family-vpnv6 unicast
#address-family-vpnv6 unicast
Step 32
Cisco Dynamic Fabric Automation Migration Guide
OL-31503-01
31
Migration Configuration
Configuring the BGP Route Reflector on a Spine