Cisco Cisco Catalyst 6500 Series 10 100 1000 BASE-T Fabric-Enabled Module Weißbuch
Wireless LAN Design Guide for High Density
Client Environments in Higher Education
17 © 2011 Cisco and/or its affiliates. All rights reserved.
802.11n - 20 MHz or 40 MHz Channels?
802.11n can operate in a 40 MHz channel by bonding two 20 MHz channels together and this significantly increases throughput.
However, this is reserved for burst mode transfers only. It is only practical to do this in 5 GHz because 2.4 GHz is already limited
by the number of channels available. If there are enough 5 GHz channels to achieve the WLAN goals using a bonded channel
plan (9 in the U.S. if using available DFS channels) to meet throughput goals, consider it. If forced to reuse 5 GHz channels, more
consistent results will be delivered using strictly 20 MHz channels and avoiding loss of efficiency due to CCI.
However, this is reserved for burst mode transfers only. It is only practical to do this in 5 GHz because 2.4 GHz is already limited
by the number of channels available. If there are enough 5 GHz channels to achieve the WLAN goals using a bonded channel
plan (9 in the U.S. if using available DFS channels) to meet throughput goals, consider it. If forced to reuse 5 GHz channels, more
consistent results will be delivered using strictly 20 MHz channels and avoiding loss of efficiency due to CCI.
Evaluating Requirements for 2.4 GHz and 5 GHz Connection Support
The essential question for a high-density design is how many channels for each band will be needed to match the client base?
This can be a tricky question since even dual band capable clients do not always select the faster 5 GHz band. Since bandwidth
in 2.4 GHz is going to be limited, 5 GHz must be relied on to reach the goal.
This can be a tricky question since even dual band capable clients do not always select the faster 5 GHz band. Since bandwidth
in 2.4 GHz is going to be limited, 5 GHz must be relied on to reach the goal.
Dual band adapters have been shipping with most laptops for some time. This does not mean that every laptop is a dual band
client, but many are. Simply having a dual band client does not guarantee that it will choose 5 GHz over 2.4 GHz. The Microsoft
Windows operating system defaults to a Wi-Fi channel search that starts with the 5 GHz channel 36 and continues searching
through all of the 5 GHz channels that the client is capable of. If no 5 GHz AP is found then it will continue the search in 2.4 GHz
starting at channel 1. Unless the Windows default is changed or the user has chosen a third party Wi-Fi utility to set spectrum
preference to 2.4 GHz, the client radio will first try to associate to a 5 GHz AP. Apple Computer’s latest release for Atheros and
Broadcom chipsets also searches 5 GHz first.
client, but many are. Simply having a dual band client does not guarantee that it will choose 5 GHz over 2.4 GHz. The Microsoft
Windows operating system defaults to a Wi-Fi channel search that starts with the 5 GHz channel 36 and continues searching
through all of the 5 GHz channels that the client is capable of. If no 5 GHz AP is found then it will continue the search in 2.4 GHz
starting at channel 1. Unless the Windows default is changed or the user has chosen a third party Wi-Fi utility to set spectrum
preference to 2.4 GHz, the client radio will first try to associate to a 5 GHz AP. Apple Computer’s latest release for Atheros and
Broadcom chipsets also searches 5 GHz first.
feature enables the infrastructure to optimize these types of client connection choices. Where possible, it
helps make sure that devices are attaching to the 5 GHz spectrum channels where interference sources tend to be significantly
lighter. A much greater channel selection leads to the alleviation of bandwidth challenges.
lighter. A much greater channel selection leads to the alleviation of bandwidth challenges.
Tablet computers and smartphones have begun entering the market at a staggering rate. The vast majority of smartphones
shipping today operate in 2.4 GHz only. While many of them are 802.11n clients, of these most have implemented a single input
single output (SISO) rather than Multiple Input, Multiple Output (MIMO). A SISO device is only capable of supporting MCS7 data
rates, or 54 Mbps.
shipping today operate in 2.4 GHz only. While many of them are 802.11n clients, of these most have implemented a single input
single output (SISO) rather than Multiple Input, Multiple Output (MIMO). A SISO device is only capable of supporting MCS7 data
rates, or 54 Mbps.
Design point #4: 5 GHz Support will be Critical for High Density, so Determine the Channel
Plan that you will Support and How it will be Administered
Evaluating the particular client mix for the WLAN can be done easily on Cisco wireless networks by utilizing the reporting features
in the Cisco Wireless Control System or by reviewing the WLAN controller’s connection logs.
in the Cisco Wireless Control System or by reviewing the WLAN controller’s connection logs.
Determine the Number of Channels and Cells Needed
A sample high-density WLAN project may include a design that yields 300 Mbps consistently to support 300 concurrent users.
Under optimal conditions, 802.11g and 802.11a data rates yield 25 Mbps throughput. However, a high-density environment will
be less than optimal from a SNR standpoint. A better number to use is 20 Mbps throughput. Table 4 provides a quick reference
using 20 Mbps per cell and per channel as the throughput value. Looking strictly at 5 GHz and assuming no channel reuse at this
point, it is clear that 1 Mbps per user with 15 channels and 15 cells can be easily supported.
Under optimal conditions, 802.11g and 802.11a data rates yield 25 Mbps throughput. However, a high-density environment will
be less than optimal from a SNR standpoint. A better number to use is 20 Mbps throughput. Table 4 provides a quick reference
using 20 Mbps per cell and per channel as the throughput value. Looking strictly at 5 GHz and assuming no channel reuse at this
point, it is clear that 1 Mbps per user with 15 channels and 15 cells can be easily supported.