Brother RJ-4040 Anleitung Für Quick Setup

Thank you for purchasing the Brother RuggedJet RJ-4030/ 

RJ-4030Ai/RJ-4040 mobile printer.

For RJ-4030/4040
Be sure to read the User’s Guide (CD-ROM), Product Safety Guide 

(Printed), Quick Reference Guide (this manual), Software User’s 

Guide (CD-ROM) and Network User’s Guide (CD-ROM:RJ-4040 only) 

before using the printer.

For RJ-4030Ai
Be sure to read the User’s Guide , Product Safety Guide (Printed), 

Quick Reference Guide (this manual), Software User’s Guide before 

using the printer. User’s Guide and Software User’s Guide can be 

found on the Brother Solutions Center at support.brother.com.

We suggest that you keep these documents in a handy place for 

future reference. To download the latest manuals, please visit the 

Brother Solutions Center at (support.brother.com), where you can also 

download the latest drivers and utilities for your printer, read FAQs and 

troubleshooting tips or learn about special printing solutions.

Printed in China

LBF110001

Front

 

„

1

2

3

4

5

6

7

8

9

10

11

12

13 14

Back

 

„

15

16

17

AC/DC connector

1 

Serial port

2 

USB port

3 

Cover open lever

4 

RD Roll compartment cover

5 

Paper outlet

6 

7 

 (Power) button  

(To turn the printer on/off)

8 

 (Feed) button  

(To feed the paper or print the 

printer settings)

POWER indicator

9 

STATUS indicator

10 

BATT (Battery) indicator

11 

12   (Bluetooth) indicator (RJ-4030/

RJ-4030Ai)/

 (Wi-Fi) 

indicator (RJ-4040)

Bluetooth button (RJ-4030/ 

13 

RJ-4030Ai)/Wi-Fi button (RJ-4040)  

(To communicate with your 

Bluetooth-equipped computer/

adapter or your network access 

point/router)

Belt hook

14 

Battery cover

15 

Battery cover latch

16 

Battery compartment

17 

„

Connect the printer to a nearby AC power outlet to power the printer 

or charge the rechargeable battery using AC power.

Connect the AC adapter to the printer.

a 

Connect the AC power cord to the AC adapter.

b 

Connect the AC power cord to a nearby AC power outlet 

c 

(100 - 240 VAC, 50 - 60 Hz).

1

2

AC adapter

1 

AC power cord

2 

„

Connect the printer to your vehicle’s 12 V DC power outlet (cigarette 

lighter, etc.) to power the printer or charge the rechargeable battery 

using the vehicle’s DC power.

Connect the Car adapter to the vehicle’s 12 V DC power outlet.

a 

Connect the Car adapter to the printer.

b 

3

Car adapter

3 

„

Open the battery cover by pressing the cover latch, and then swing 

a 

the cover open and remove it.  

Insert the battery into the battery compartment.

1

2

Battery cover

1 

Cover latch

2 

Confirm that the hooks on the edge of the battery cover are inserted 

b 

correctly, and then reattach the cover.

„

Remove the battery cover and the rechargeable Li-ion battery, and 

then reattach the battery cover.
Charging the Rechargeable Li-ion Battery

„

Make sure that the printer is turned off. If the printer is turned on, 

a 

press and hold the   (Power) button to turn it off.
Make sure that the rechargeable Li-ion battery is installed in the printer.

b 

Use the AC adapter and AC power cord to connect the printer to an 

c 

AC power outlet, or use the Car adapter to connect the printer to a 

DC power outlet.
The BATT (battery) indicator light is orange when the printer is charging.
When the rechargeable Li-ion battery is fully charged, the BATT 

(battery) indicator light turns off. Disconnect the AC power cord or 

Car adapter from the battery’s AC/DC connector.

For details, see the User’s Guide.

= Indicator is lit

G = Green
O = Orange
R = Red
B = Blue

= Indicator is blinking

= Indicator blinks 1 or 2 times in each color, then 

turns off

= Indicator is lit or blinking in any color or pattern

(off) = Indicator is off

Example: 

 = Indicator is blinking in green

Power on

Roll cover open

Receiving data
Transferring data

Error

Print error
Feed error
Cover open error
Communication error
Image processing error
Database search error
No template error
Access point search error
Access point connection error
Security error

(off)

Error

Battery error
Mass storage error

(off)

System error

(off)

(off)

(off)

In boot mode

(Once every 

3 seconds)

Wireless on, not connected*

Wireless or Bluetooth on, connected

(Once every 

second)

Now setting WPS*

(off)

Now resetting

Formatting complete (When [

Data after being Printed] is set to 

[

Erase])

Now cooling

MCR read mode

(off)

MCR read success

(off)

MCR read error

(Once every 

4 seconds)

Rechargeable battery power: half

(Twice every 

4 seconds)

Rechargeable battery power: low

(Once every 

second)

Battery must be charged

Charging

(off)

Rechargeable battery power: full
Charging complete

(off)

In mass storage mode

Processing file in mass storage mode

(off)

(off)

Initializing

*RJ-4040 only

Is the cable loose?

 

„

Check that the cable is connected securely.
Is the RD Roll installed correctly?

 

„

If not, remove the RD Roll and reinstall.
Is there enough roll remaining?

 

„

If not, install a new RD Roll.
Is the RD Roll compartment cover open?

 

„

Check that the RD Roll compartment cover is closed.
Has a print error or transmission error occurred?

 

„

Turn off the printer and on again. If the problem still occurs, contact Brother Customer Service.
Is the roll guide not touching the side of the RD Roll?

 

„

Move the roll guide against the side of the RD Roll.

Is the power cord inserted correctly?

 

„

Check that the power cord is inserted correctly. If it is, try plugging it into another electrical 

outlet.
If the POWER indicator still does not light up, contact Brother Customer Service.

 

„

Printed labels contain streaks or poor quality characters, or labels are not fed correctly.
Is the print head or roller dirty?
Although the print head generally remains clean under normal use, lint or dirt from the roller may 

become stuck on the printer head. If this occurs, clean the roller.
A data transmission error appears on your computer.

Is the correct port selected?

 

„

Check that the correct port is selected.
Is the printer in cooling mode (the POWER indicator is flashing in orange)?

 

„

Wait until the indicator stops flashing and then try printing again.
Is someone printing via the network?

 

„

If you try to print while other users are printing large amounts of data, the printer is unable to 

accept your print job until the ongoing printing is finished. In such situations, execute the print 

job again after the other jobs are completed.

Is there dirt or lint on the roller preventing it from rolling freely?

 

„

Check that the ejection path of the label is not blocked.

 

„

Check that the RD Roll is set correctly by removing the RD Roll and reinstalling.

 

„

Ensure that the RD Roll compartment cover is closed correctly.

 

„

The print quality is poor.
Is there dirt or lint on the roller preventing it from rolling freely?
Clean the roller.
Printed barcodes cannot be read.

Align the label with the print head as shown below.

 

„

1

2

3

Label exit slot

1 

Print head

2 

Recommended print direction

3 

Some types of scanners are not able to read the barcodes. Try using another scanner.

 

„

We recommend setting [

 

„

Quality] in the printer properties window to [Give priority to print 

quality] when printing barcodes.

I want to reset the printer/delete the data transferred from the computer.
To reset the printer, perform the following procedure;

Press and hold the 

1 

 (Power) button to turn the printer off.

Press and hold the 

2 

 (Feed) button and the   (Power) button until the POWER, STATUS 

and BATTERY indicators start blinking in orange.
While pressing the 

3 

 (Power) button, press the 

 (Feed) button 3 times.

Release the 

4 

 (Power) button and the 

 (Feed) button at the same time.

All the transferred data from the computer will be deleted and reset the printer to factory settings.
I want to cancel the current print job.
Make sure that the printer is ON, and press the   (Power) button.

Maintenance of the printer may be carried out as required. However, 

some environments require that maintenance must be done more 

frequently (e.g. in dusty conditions).

„

Use a cotton swab and wipe the head.

1

Print head

1 

„

Use a piece of cellophane tape to remove dirt from the roller.

2

Roller

2 

„

If glue accumulates on the paper outlet and the printer becomes 

jammed, disconnect the printer from the external power outlet and 

clean the paper outlet with a cloth dipped in isopropyl alcohol.

3

Paper outlet

3 

Brother Global Web Site: www.brother.com

Brother Developer Center: www.brother.com/product/dev/

For Frequently Asked Questions (FAQs), Product Support and Technical 

Questions, and Driver Updates and Utilities: support.brother.com

You can use the   (Feed) button to print a report that lists the 

following printer settings:

Program version

 

„

Printer usage history

 

„

Missing dot test pattern

 

„

RJ Utility setting information

 

„

List of transferred data

 

„

Network setting information

 

„

Wi-Fi setting information

 

„

You can use the RJ Utility to set in advance which items will be 

• 

printed.
The node name appears in the Printer Settings. The default node 

• 

name is “BRWxxxxxxxxxxxx”. (“xxxxxxxxxxxx” is based on your 
printer’s MAC Address / Ethernet Address.)

Make sure that a roll of 4" (101.6 mm) receipt paper has been 

a 

loaded and the RD Roll compartment cover is closed.
Turn on the printer.

b 

Press and hold the 

c 

 (Feed) button until the POWER indicator 

starts blinking in green.  

The settings will be printed.

To print the Printer Settings, we recommend to use 4" (101.6 mm) 

• 

receipt paper.
This operation can also be performed using the RJ Utility.

• 

For details, see the User’s Guide.

Install the printer driver and the software.

a 

Make sure that the printer is correctly powered. Use a charged 

b 

battery or connect the printer to an AC or DC power outlet.
Turn the printer on. The POWER indicator should be green.

c 

Connect the printer to a computer or handheld device using either USB, 

d 

Bluetooth, or Wi-Fi.
Insert the RD Roll.

e 

Print receipts or labels.

f 

For details, see the User’s Guide.

Press and hold the 

a 

 (Power) button to turn the printer off.  

Turn and hold the cover open lever, and then open the RD Roll 

compartment cover.

While pushing the adjuster lock in the direction of the arrow, move 

b 

it to the left or right. Because the roll guide will also move, adjust 

the roll guide to match the width of the paper using the scale 

engraved on the inside of the printer.

1

2

3

2

Adjuster lock

1 

Roll guide

2 

Scale

3 

Insert an RD Roll into the RD Roll compartment upside down with 

c 

the labels feeding from the bottom as shown. 

Align the RD Roll with the guide lines.

5

4

Guide lines

4 

Tear bar

5 

Close the RD Roll compartment by pressing on the center of the cover, 

d 

and then press and hold the   (Power) button to turn the printer on.

printing.
Is the printer set for sequential printing?
If so, set print mode to buffered printing.
For Windows Vista

®

 / Windows Server

®

 2008:  

Open printer properties from [

Control Panel] - [Hardware and Sound] - [Printers] and click 

[

Printing Preference] button in the [General] tab. Click the [Other] tab and choose the option 

[

After one page of data is received].)

For Windows

®

 7 / Windows

®

 8 / Windows

®

 8.1 / Windows Server

®

 2008 R2 / Windows Server

®

 

2012 / Windows Server

®

 2012 R2:  

Open printer properties from [

Devices and Printers], right-clicking the printer whose settings are 

to be changed, and selecting [

Printing Preference]. Choose the option [After one page of data 

is received].
For Windows

®

 10:  

Open printer properties from Start button - [

Settings] - [Devices and Printers], right-clicking the 

printer whose settings are to be changed, and selecting [

Printing Preference]. Choose the option 

[

After one page of data is received].

An error occurs when the roll cannot be fed to the beginning of the label.
If a feed error occurs, use the Custom Label Tool to assign the correct paper settings to the printer.
The computer program should be sending data to the printer, but the POWER indicator 

does not blink green.
Make sure that the USB cable is connected firmly and correctly. Try using another USB cable.
Depending on whether you are using Bluetooth or Wi-Fi, confirm that the   (Bluetooth) indicator 

or the 

 (Wi-Fi) indicator is lit in blue. If it is not, check the connection.

Make sure that you are logged on with Administrator rights.

The screenshot shown below may differ slightly from that of the actual 

product.

Insert the installer CD-ROM into your CD-ROM drive. If the model 

a 

name screen appears, choose your printer. If the language screen 

appears, choose your language.
Click [

b 

Standard Installation].

You can refer to the User’s Guide by clicking [

 

„

User’s Guide].

Read the license agreement and click [

c 

Agree] if you agree with the 

terms and conditions.
Click [

d 

Install] to start the installation and follow the on-screen 

instructions to complete the Standard Installation.

You can download optional tools later from the Brother Solutions 
Center:  
support.brother.com  
[

Select your region/country] - Choose your product - [Downloads]

For details, see the User’s Guide.

For RJ-4030Ai
Please install the printer driver and P-touch Editor software before 

using the printer.

Visit our website (

a 

www.brother.com/inst/) and download the 

installer for the software and documents.
Double-click the downloaded .exe file and follow the on-screen 

b 

instructions to proceed with the installation. In the dialog box for 

selecting which items to install, select the necessary software.

In order for the printer and your Bluetooth-equipped 

computer or adapter to communicate, you must first pair 

the printer with the computer or handheld device using the 

Bluetooth management software.

Press and hold the 

a 

 (Power) button to turn the printer on, and 

then press the Bluetooth button.
Use your Bluetooth management software to discover the printer.  

b 

Bluetooth communication is now active.

In order for the printer and your network access point or 

router to communicate, you must first install the printer 

driver and Printer Setting Tool. 

Press and hold the 

a 

 (Power) button to turn the printer on, and 

then press the Wi-Fi button.  

Wi-Fi communication is now active.

For details, see the User’s Guide.