Acumen jog mate plus Benutzerhandbuch

Step 4) Press and hold the “P ” button for one

second till the current stride setting is in display

and flashing.

Step 5) Bring the unit back to its original position

by flipping it downward. Go ahead and walk or

run the measured 30 feet (10m) while the display

is flashing.

Step 6) Press the “P ” button once again. The

display will cease flashing. The number that now

appears on the screen is your automatically

calculated stride. To check for accuracy, repeat

the above procedure.

Step 1) Determine your WALK or RUN stride by

walking or running the previously measured 30

feet (10m) and count the number of steps you take.

Step 2) Take the number of steps and divide it

into 30 feet (or 10m) For example: 30 feet divided

by 10 steps taken is 3 feet.

Step 3) Enter the calculated stride value by pressing

“F ” button to first get into the DISTANCE mode.

Step 4) Press and hold “P ” button for one second

till the stride setting is located.

Acumen Inc.

P/N: 

81-967428-00

Step 5) Press the   /   buttons to either increase

or decrease the stride (each increment /decrement

is 0.1 feet or 0.05m) until the desired number is

located.

Step 6) Press the “P ” button once again to

stop the flashing screen and switch back to the

DISTANCE mode display. Your stride is now

locked in the unit.

flashing. Press the “ ” or “ ” buttons to increase

or decrease the hour. Press the “P ” button again and

the minutes will flash. Use the “ ” or “ ” buttons

to change the minutes. Press the “P ” button

once more and the time is locked in. You can

display the time whenever you wish without

affecting the recording of the unit.

Notes for Button Function:
F : Function   P : Program    : Time

 : Increase     : Decrease

The KM/Miles switch is located inside the battery

compartment. To change the unit setting,

remove the battery and use a pen to set your

desire unit. See below figures.

STOPWATCH

CALORIES

DISTANCE

STEPS

TIME

AVERAGE SPEED

Step 1) Press the  “F ” button repeatedly to get

into the CALORIES mode where the data of

calories burned during the exercise is displayed.

Step 2) Press and hold the “P ” button for one

second until the current weight setting of 175 (lbs)

appears and flashing.

To stop recording your distance travelled, press

the Start/Stop button again. The Running Man

will stop running.

Flip up the unit to enter the AUTO STOP/SCAN

mode. The unit will automatically stop all

measuring and begin to scan all of the data

that have just been recorded, one by one

from STOPWATCH, DISTANCE, STEPS,

CALORIES, to AVERAGE SPEED, and back

to whichever mode the unit was in before the

unit was flipped. Bring the unit back to its

original position by flipping it downward. Press

the Start/Stop button to begin measuring again.

You may press the “F ” button to toggle between

the following modes.

usage and does not cover damage which

occurs in shipment or failure which results from

accident, misuse, abuse, tampering, alteration

or disassembling of the product or improper

maintenance. This warranty is effective only

if the product is purchased and operated in the

USA and does not extend to any units which

have been used in violation of written

instructions furnished by Acumen Inc. or to

units which have been altered or modified

without authorization of Acumen Inc., or to

damage to products or parts thereof which

have had the serial number removed, altered,

defected or rendered illegible.

Do not attempt to repair your product. Should

the product malfunction, you should first call

(703) 904-0405 between the hours of 9am-

5pm Eastern Time and ask for CONSUMER

CUSTOMER SERVICE stating that you are a

consumer with a problem. If the problem cannot

be resolved, you will be asked to return the

product to the factory for repair. Under no

circumstances should you attempt to open

housing and repair the product. Should you do

this, your warranty will be voided.

Securely package and return the product,

PREPAID to:

Be sure to enclose:
a. Your name, address and phone number.
b. The date of purchase (or receipt as a gift)
c. An explanation of the malfunction or reason

    for return.
d. Seven dollars and fifty cents ($7.50) Check

    or Money Order payable to Acumen Inc.

    for return postage and handling.
e. To insure prompt  ‘In warranty’ service, be

    sure to include proof of date of purchase.

We recommend you take the necessary

precaution of insuring the parcel.

Battery Door

Unit Switch

Mi

Km

RUN modes in the JogMate Plus are, respectively,

2’0’’(~0.6m) and 3’0’’(~0.9m). These are

averages taken from adult males. In order to

achieve accurate mileage results from your

JogMate Plus, it is important that both lengths

of your walking and running strides are correctly

entered into the unit. This can be done in two

ways, which are having the JogMate Plus

automatically calculate the stride or manually

inputting the stride lengths. For either case,

first plan a route for your exercise and measure

out a distance of exactly 30 feet (10m) for the

calculations.

Step 1) Clip the JogMate Plus to your waist

per the above instructions. You may flip-up the

unit using the spring loaded clip for easy viewing

and operation of the unit.

Step 2) Press the Walk/Run button to toggle

between WALK or RUN modes. Chose one at

a time to enter the stride.

Step 3) Press the “F ” button to get into the

DISTANCE mode where the word “Miles”

following three number digits appears on the

screen.

• Automatic or manual stride adjustment for

  accuracy
• Measuring the distance travelled in miles (KM)

  and steps
• Stopwatch
• Measuring calories burned
• 12 hour clock
• Average speed of trip
• Independent “ WALK ” / “ RUN ” settings
• “Auto Stop / Scan” function

In order to get the most accurate results from

your JogMate Plus, please read the instructions

completely. This electronic pedometer should be

worn as close to the center of your body as

possible (Just to the left or right of your belt

buckle). Walk on hard level surfaces such as a

road, track or walking path. Take even strides

when walking or running and avoid sudden or

sharp turns.

The Two default stride settings for WALK and

Step 3) Press the   /   buttons to either increase

or decrease the weight setting until the desired

number is located.
Step 4) Press the “P ” button once again to

stop the flashing screen and switch back to the

CALORIES mode display. Your weight is now

locked into the program and allows the unit to

calculate the calories burned during your exercise.

Attach your JogMate Plus as previously

instructed. The pedometer, by default, begins in

the TIME mode after being powered up.

Press the Start/Stop button once the unit will

go into the STOPWATCH mode, where the

elapsed time of the exercise is measured. The

Running-Man figure in the lower left hand corner

of the display will also begin to run. This indicates

that the unit is now ready to record your distance.

• The Reset button on the JogMate Plus is

   operational ONLY when the unit is stopped,

   which is indicated by the Running Man being

   static.

• Press the Reset button to set the unit back

  to zero. It will reset the data recorded in all

  modes except your recorded stride settings.

• Do not press the Reset button if you want

  to save and accumulated the results over a

   period of time. In this way, the unit will show

   where you left off from the previous exercise

   period.

Press the “ ” button once. This will display the time

of day. To change the time, press and hold the

“P ” button  for one second, the hour will start

Use a coin to open the battery cover. Remove the

cover and replace the battery. When finish, turn the

cover clockwise until it locks in place. You will

need to reset your stride and the clock as these

have been erased.

Battery Type: Lithium CR 2032

Battery Life: Approximately 1.5 years

• Do not drop the unit.
• Do not expose the unit to moisture or high
  humidity.
• Do not expose the unit to high temperatures

This product is warranted by Acumen Inc. for

one year from date of purchase (with the

exception of batteries) against defects in

workmanship and material. During that period,

these defects will be repaired or the product

will be replaced at Acumen Inc. option without

charge. This warranty covers normal consumer