Alesis wildfire Benutzerhandbuch

Seite von 48
 
 
 
 
 
 
 
 
 
 
 
 
User Manual 
 
 
 
 
 

Zusammenfassung der Spezifikationen benutzerhandbuch für Alesis wildfire

  • Seite 1User Manual
  • Seite 2 This page intentionally left blank 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
  • Seite 3: Chapter 1: IntroductionTable Of Contents Chapter 1: Introduction .............................................. 3 About the Wildfire....................................................................4 Wildfire Basics .........................................................................5 How to Use This Manual .........................................................7...
  • Seite 4: About the Wildfire Table of Contents This page intentionally left blank 2
  • Seite 5: Wildfire Basics1 Introduction Welcome! Thank you for making the Alesis Wildfire a part of your For more effective service setup. Since...
  • Seite 61 Introduction About the Wildfire Our Wildfire guitar amplifiers are compact and light, but extremely powerful. Perfect for both practicing...
  • Seite 7: How to Use This Manual Introduction 1 Wildfire Basics Benefits of an On-Board Effect Processor If you use guitar effects, you probably do so...
  • Seite 81 Introduction Parameters A parameter is a control that changes the characteristics of an effect. When we use the word...
  • Seite 9: Chapter 2: Hookup Diagram Introduction 1 How to Use This Manual This manual is divided into the following sections describing the various functions...
  • Seite 101 Introduction This page intentionally left blank 8
  • Seite 11: Front Panel2 Hookup Diagram The first thing we’ll show you is how to get your Wildfire up and running. The following...
  • Seite 122 Hookup Diagram This page intentionally left blank 10
  • Seite 133 A Tour of the Wildfire The diagrams in this section illustrate the features you’ll find on the Wildfire’s front...
  • Seite 143 A Tour of the Wildfire Input Plug in your guitar here using a guitar patch cord. You can also...
  • Seite 15: Rear Panel A Tour of the Wildfire 3 EFFECT Knob The EFFECT knob is used for selecting effect modules, parameters and...
  • Seite 163 A Tour of the Wildfire BASS Knob (Wildfire 60 only) This knob gives you the ability to equalize (EQ)...
  • Seite 17: Chapter 4: Selecting Programs A Tour of the Wildfire 3 Rear Panel All three Wildfire models offer the rear-panel features described here: Fuse...
  • Seite 183 A Tour of the Wildfire accepts a 1/4” plug. Expression pedals may be purchased at your local Alesis dealer....
  • Seite 19: Chapter 5: Editing Programs4 Selecting Programs After you’ve plugged everything in, you’ll probably want to check out the factory presets we programmed into...
  • Seite 204 Selecting Programs This page intentionally left blank 18
  • Seite 21: Chapter 6: Storing & Copying Programs5 Editing Programs To Edit a Selected Program 1. Select a program to edit using the Program Up and Down...
  • Seite 225 Editing Programs This page intentionally left blank 20
  • Seite 23: Chapter 7: Using the Tuner6 Storing & Copying Programs To Store a Program 1. In PLAY or EDIT mode, press the VALUE knob. The...
  • Seite 246 Storing & Copying Programs Arranging Programs for Performance You can use the copy function to arrange programs logically for...
  • Seite 25: Chapter 8: Deferred Program Change7 Using the Tuner To Tune Your Guitar 1. In Play mode, enter BYPASS or MUTE mode by pressing the...
  • Seite 267 Using the Tuner Visual Guide to Tuning Here are the 12 possible Low pitches (a decimal point indicates a...
  • Seite 27: Chapter 9: Stereo-Linking Two Amplifiers8 Deferred Program Change When you switch programs, the Wildfire normally changes immediately to the program shown on the display....
  • Seite 288 Deferred Program Change This page intentionally left blank 26
  • Seite 29: Chapter 10: EFFECT Knob Settings9 Stereo-Linking Two Amplifiers To take full advantage of the Wildfire’s stereo capability, you can link it to another amplifier...
  • Seite 309 Stereo-Linking Two Amplifiers This page intentionally left blank 28
  • Seite 3110 EFFECT Knob Settings Following are descriptions of each of the effect modules (and other settings of the EFFECT knob),...
  • Seite 3210 EFFECT Knob Settings DIST (Distortion) This setting adds that universal effect that was first used in rock music decades...
  • Seite 33 EFFECT Knob Settings 10 DRIVE This is a parameter of the DIST module. Increasing levels of drive/gain for the...
  • Seite 3410 EFFECT Knob Settings Noise Reduction (Right digit of display) Increasing levels of gate threshold. Turns off noise reduction. CAB...
  • Seite 35 EFFECT Knob Settings 10 Pedal-Controlled Phaser A phaser effect with its feedback controlled by the expression pedal. Tremolo Varies...
  • Seite 3610 EFFECT Knob Settings Flanger Shifts the pitch of the signal up and down, creating a swirling effect. Higher values...
  • Seite 37 EFFECT Knob Settings 10 PARAM (Direct-Control Parameter for FX1) This parameter modifies the operation of the effect selected for...
  • Seite 3810 EFFECT Knob Settings PARAM (Direct-Control Parameter for FX2) These parameters work exactly the same way as the direct-control parameter...
  • Seite 39 EFFECT Knob Settings 10 Pedal Stereo Delay A Stereo Delay effect for which the feedback level is controlled by...
  • Seite 4010 EFFECT Knob Settings Chorus – same as in FX1. Pedal Chorus – same as in FX1. Flanger – same...
  • Seite 41: Chapter 11: Troubleshooting EFFECT Knob Settings 10 Indicates that the expression pedal controls the parameter. Indicates FX3 is off. DIGFX (Digital Sampling...
  • Seite 4210 EFFECT Knob Settings ROUTE In this position, the display indicates the current signal-routing order of the FX modules. This...
  • Seite 43: Chapter 12: Specifications11 Troubleshooting Symptoms Cause Solution Wildfire does not Unit not plugged in. Make sure the power cord function (no display...
  • Seite 4411 Troubleshooting This page intentionally left blank 42
  • Seite 45: Chapter 13: Contact Information12 Specifications Output Power Rating Wildfire 15: 15W RMS Mono in 8Ω Wildfire 30: 30W RMS Mono in 8Ω Wildfire...
  • Seite 4612 Specifications Stereo Link Output Output Connector: 1/4” TS (Unbalanced) Output Impedance: 2.2Ω Max Output Level: 2.4Vp (100KΩ load) Destination...
  • Seite 4713 Contact Information Alesis Distribution, LLC Los Angeles, USA E-mail: support@alesis.com Website: http://www.alesis.com Wildfire User Manual Version 1.0 by Edwin...
  • Seite 487-51-0148-C
downloadlike
ArtboardArtboardArtboard
Report Bug