ART sgx 2000 Benutzerhandbuch
28
When you choose the Panner, the signal is automatically panned by the SGX 2000
from left to right at a depth and speed you set. Choosing the MIDI-PAN allows you
to assign a MIDI Controller to change the signal's position with an Expression
Pedal or other MIDI device.
from left to right at a depth and speed you set. Choosing the MIDI-PAN allows you
to assign a MIDI Controller to change the signal's position with an Expression
Pedal or other MIDI device.
NOTES:
1) When using the panner, you should always set your MIX DRY level to 0%. This
ensures complete signal panning from left to right (full right = full signal...
no signal left and vice versa).
2) When you use the Panner, make sure you are using both Line outputs or the
Headphone outputs, if you're using only one Line output or the Instrument output
you'll get NO EFFECT!, because the two outputs are summed canceling the effect.
1) When using the panner, you should always set your MIX DRY level to 0%. This
ensures complete signal panning from left to right (full right = full signal...
no signal left and vice versa).
2) When you use the Panner, make sure you are using both Line outputs or the
Headphone outputs, if you're using only one Line output or the Instrument output
you'll get NO EFFECT!, because the two outputs are summed canceling the effect.
TREMOLO
[TREMOLO], [TRM]
[TREMOLO], [TRM]
Parameters:
:MOD % =0 to 100 percent in % increments [100%]
:SPEED= .04Hz to 27.3Hz [2.16Hz]
:MOD % =0 to 100 percent in % increments [100%]
:SPEED= .04Hz to 27.3Hz [2.16Hz]
Tremolo creates an amplitude modulating effect at the output. The actual output
signal level is being cut in and out at a certain rate. Use the MOD parameter to
control the depth of the Tremolo. Re-create the effect found on vintage as well
as current guitar amplifiers.
signal level is being cut in and out at a certain rate. Use the MOD parameter to
control the depth of the Tremolo. Re-create the effect found on vintage as well
as current guitar amplifiers.
NATURAL REVERBERATION ALGORITHMS
REVERB-1
[REVERB-1], [REV]
[REVERB-1], [REV]
Parameters:
:TYPE= HALL-1, ROOM-1, PLATE-1, VOCAL-1, OFF [HALL-1]
:IN = PRE DDL, POST DDL [PRE DDL]
:DECAY = 0 to 25 seconds in varying increments [2.4s]
:HFDAMP = 0 to 50 percent in % increments [14%]
:POSITN= FRONT to REAR in % increments [83%]
:LEVEL = 0 to 100 percent in % increments [100%]
:TYPE= HALL-1, ROOM-1, PLATE-1, VOCAL-1, OFF [HALL-1]
:IN = PRE DDL, POST DDL [PRE DDL]
:DECAY = 0 to 25 seconds in varying increments [2.4s]
:HFDAMP = 0 to 50 percent in % increments [14%]
:POSITN= FRONT to REAR in % increments [83%]
:LEVEL = 0 to 100 percent in % increments [100%]
REVERB-2
[REVERB-2], [REV]
[REVERB-2], [REV]
Parameters:
:TYPE= HALL-2, ROOM-2, PLATE-2, VOCAL-2, OFF (REVERB-1 TYPEs are also available)
[HALL-2]
:IN = PRE DDL, POST DDL [PRE DDL]
:DECAY = 0 to 25 seconds in varying increments [2.4s]
:HFDAMP= 0 to 50 percent in % increments [14%]
:POSITN= FRONT to REAR in % increments [83%]
:LEVEL = 0 to 100 percent in % increments [100%]
:TYPE= HALL-2, ROOM-2, PLATE-2, VOCAL-2, OFF (REVERB-1 TYPEs are also available)
[HALL-2]
:IN = PRE DDL, POST DDL [PRE DDL]
:DECAY = 0 to 25 seconds in varying increments [2.4s]
:HFDAMP= 0 to 50 percent in % increments [14%]
:POSITN= FRONT to REAR in % increments [83%]
:LEVEL = 0 to 100 percent in % increments [100%]
REVERB-3
[REVERB-3], [REV]
[REVERB-3], [REV]
Parameters: