HP dx2100 Benutzerhandbuch

© 

2005 Hewlett-Packard Development Company, L.P. The informa-

tion contained herein is subject to change without notice. HP shall 
not be liable for technical or editorial errors or omissions contained 
herein. Intel, Pentium, Intel Inside, and the Intel logo are trademarks 
or registered trademarks of the Intel Corporation and its subsidiaries 
in the U. S. and other countries. 

Document Number 404568-001.     1st Edition November 2005.

Basic system information regarding system information, setup, power management, hardware, 
and passwords is maintained in the Setup Utility held in the system ROM. The Setup Utility is 
accessed by pressing the F10 key when prompted (on screen) to do so during the boot sequence. 
If the screen prompt opportunity is missed, a restart will be necessary.

Processor Type:

Intel Celeron D or Pentium 4

RAM Type:

DDR PC2 4200, non-ECC

Maximum RAM Supported:

4 GB

Expansion Bus:

PCI 2.2

Graphics Adapter

Integrated controller. PCI-e support.

Hard drive interface:

SATA 1.5 Gb/s

I/O Interfaces:

Serial (1), parallel (1), USB 2.0 (6), diskette drive (1)

System 
Information

Lists the following main system specifications:

•

Product Name

•

SKU number

•

Processor Type

•

Processor Speed

•

CPU  ID

•

Cache Size

•

Memory Size

•

System ROM

•

Integrated MAC Address

•

UUID

•

System serial number

•

Asset tag number

Standard 
CMOS 
Setup

Date (mm/dd/yy) - Allows you to set system date.

Time (hh:mm:ss) - Allows you to set system time.

PATA Controller - Disables/enables PATA controller

PATA Ch 0 Master/PATA Ch 0 Slave - Allows you to detect IDE HDD 
size in selected channel, set UIDE on selected channel, set access mode 
on selected channel, view firmware version, and capacities, run SMART 
HDD status, and perform various SMART tests.

SATA Controller - Disables/enables controller and both SATA and 
PATA channels.

PATA IDE Mode - Allows you to identify if the PATA device is for the 
primary or secondary channel.

SATA Port - Displays the SATA Port settings.

PATA Ch 0 Master/PATA Ch 1 Master - Allows you to detect HDD size 
in selected channel, set extended drive on selected channel, set access 
mode on selected channel, view firmware version, and capacities, run 
SMART HDD status, and perform various SMART tests.

Floppy Controller - Disables/enables floppy drive controller.

Drive A - allows you to set floppy drive to None or 1.44, 3.5 in.

Halt On - Allows you to set POST error behavior.

POST Delay - Allows you to set a POST delay to 1, 5, 10, 15, or 30
seconds.

Advanced 
BIOS Fea-
tures

Device Boot Disabling - Allows you to restrict a device from booting.

Removable Device Boot Priority - Allows you to specify the order of 
attached removable devices in the boot sequence.

Hard Disk Boot Priority - Allows you to specify the order in which 
attached HDDs are booted.

Optical Drive Boot Priority - Allows you to specify the order in which 
attached ODDs are checked for a bootable operating system image.

Network Boot priority - Allows you to specify the order in which net-
work devices are checked for a bootable OS image.

F9 Boot Menu Display - Disables/enables Boot menu.

Quick Power On Self Test - Disables/enables system to skip select tests 
while booting.

First, Second, or Third Boot Device - Allows you to specify boot 
sequence or disable any of the three devices.

HDD S.M.A.R.T. Capability - Disables/enables S.M.A.R.T. Capability

Boot up Numlock Status - Allows you to turn the default feature on or 
off.

Security Option - Allows you to set security to determine whether a 
password is needed for booting or when entering Computer Setup.

Hyper-Threading Technology - Disables/enables hyper-threading if the 
OCS permits it.

APIC Mode - Disables/enables APIC.

MPS Version Control for OS - Allows you to select 1.1 or 1.4 MPS table 
version.

OS Select for DRAM > 64MB -Allows you to select OS2 or Non-OS2. 
Use OS2 only when RAM is greater than 64 MB.

BIOS write Protection - Disables/enables ROM BIOS upgrading.

Advanced 
Chipset Fea-
tures

PCI Express Root Port Func - Allows you to set PCI Express Port 1 
Auto, Enabled, or disabled and also to set PCI-e Compliance Mode to 
either v1.0 or 1.0a.

On-Chip Frame Buffer Size (VGA Setting) - Allows you to set buffer 
size to 1MB or 8 MB.

DVMT Mode (VGA Setting) - Allows you to set mode to Fixed, DVMT, 
or Both.

DVMT /Fixed Memory Size (VGA Setting) - Allows you to set memory 
size to 64MB or 128 MB.

Init Display First (VGA Setting) - Allows you to set initial clock detec-
tion to PCI slot or Onboard.

Auto Detect PCI Clk - Disables/enables PCI clock auto detection.

Spread Spectrum - Disables/enables clock spread spectrum.

Integrated 
Peripherals

USB Controller - Disables/enables USB controller.

USB Legacy Support - Disables/enables USB keyboard and mouse.

Onboard Audio - Allows you to auto-detect or disable onboard audio.

Onboard LAN - Disables/enables onboard LAN controller.

Onboard LAN Boot ROM- Disables/enables Boot ROM onboard on the 
LAN chip.

Onboard Serial Port 1 - Allows you to select one of these settings: Dis-
abled, 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, or 2E8/IRQ3.

Onboard Parallel Port - Allows you to select one of these settings: Dis-
abled, 378/IRQ7, 278/IRQ5, or 3BC/IRQ7.

Parallel Port Mode - Allows you to set parallel port mode to SPP, EPP, 
ECP, or ECP+EPP.

ECP Mode use DMA - If parallel port mode set to ECP or ECP+EPP, 
allows you to set DMA channel for ECP mode to 1 or 3.

Power 
Manage-
ment Setup

ACPI Function - Disables/enables ACPI functions. Changing this can 
make the installed OS unusable.

ACPI Suspend Type - Allows you to set ACPI suspend to S1 (POS), S3 
(STR) or S1 & S3.

Soft off by Power Button - Allows you to set power button to instant off 
or 4 second delay.

Power On After Power-Fail - Allows you to select system power loss 
behavior to Last state, On, or Off.

MODEM use IRQ - Allows you to set IRQ for modem to NA (disable), 
3, 4, 5, 7, 9, 10, or 11.

Resume by PME - Disables/enable the feature.

Wake on Device S5 - Disables/enables wake device from network.

Resume by Alarm - Disables/enables RTC alarm.

Date (of Month) Alarm - If resume by Alarm is enabled, allows you to 
select the day of the month to resume RTC alarm.

Time (hh:mm:ss) Alarm - Allows you to set the time the RTC alarm will 
resume if the Resume by Alarm feature is enabled.

PnP/PCI 
Configura-
tions

Allows you to select whether resources are controlled automatically or 
manually.

IRQ Resources - When resources are manually controlled, allows you to 
assign a type to each system interrupt based on the device using it. 

Maximum Payload Size - Allows you to set TLP payload size for the 
PCI-e devices to 128, 256, 512, 1024, 2048, or 4096 bytes.

PC Health 
Status

CPU Temperature - View.

CPU Fan Speed - View.

System Fan Speed - View.

SYS Fan Fault Check - Disable/enable detection of fan failure during 
POST.

Load Opti-
mized 
Defaults

Allows you to reset Computer Setup to factory defaults.

Set Supervi-
sor Password

Allows you to set a password to control access to Computer Setup.

Set User 
Password

Allows you to set a password to control access to the Computer.

Save & Exit 
Setup

Allows you to save current settings and exit Computer Setup.

Exit With-
out Saving

Allows you to exit Computer Setup without saving changes.