Sony 4-139-513-11(1) Benutzerhandbuch
17
H
ook
up
s and
s and
Se
tti
tti
n
gs
6
Press X/x to select the setting that
matches your TV type.
matches your TV type.
◆ If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
• 16:9 (page 35)
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
standard TV with a wide-screen mode
• 16:9 (page 35)
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
7
Press ENTER.
The Setup Display for selecting the type
of video signal output from the LINE
(RGB)-TV jack appears.
of video signal output from the LINE
(RGB)-TV jack appears.
8
Press X/x to select the type of
signal you want to output from the
signal you want to output from the
LINE (RGB)-TV jack.
9
Press ENTER.
The Setup Display for selecting the type
of jack used to connect your audio
component appears.
of jack used to connect your audio
component appears.
10
Press X/x to select the type of
jack (if any) you are using to
connect to an audio component,
then press ENTER.
Select “NO,” if you do not connect an
audio component, then go to step 14.
audio component, then go to step 14.
Select “YES: LINE OUTPUT L/R
(AUDIO),” if you connect an audio
component using an audio cord, then go
to step 14.
Select “YES: DIGITAL OUTPUT,” if
you connect an audio component using a
digital coaxial cord/HDMI cord.
(AUDIO),” if you connect an audio
component using an audio cord, then go
to step 14.
Select “YES: DIGITAL OUTPUT,” if
you connect an audio component using a
digital coaxial cord/HDMI cord.
11
Press X/x to select the type of
Dolby Digital signal to your audio
component.
If your audio component has a Dolby
Digital decoder, select “DOLBY
DIGITAL.” Otherwise, select “D-PCM.”
Digital decoder, select “DOLBY
DIGITAL.” Otherwise, select “D-PCM.”
12
Press ENTER.
“DTS” is selected.
13
Press X/x to select whether or
not to send a DTS signal to your
audio component.
If your audio component has a DTS
decoder, select “ON.” Otherwise, select
“OFF.”
decoder, select “ON.” Otherwise, select
“OFF.”
14
Press ENTER.
Quick Setup is finished and connections
are complete.
If your audio component has an MPEG
audio decoder, set “MPEG” to “MPEG”
(page 39).
are complete.
If your audio component has an MPEG
audio decoder, set “MPEG” to “MPEG”
(page 39).
b
When “PhotoTV HD” mode is activated (page 32),
the selection for “TV TYPE” is skipped.
the selection for “TV TYPE” is skipped.
16:9
ON
JACKET PICTURE
VIDEO
SCREEN SETUP
TV TYPE:
BACKGROUND:
SCREEN SAVER:
LINE:
PROGRESSIVE
(COMPONENT OUT ONLY)
:
MODE
(PROGRESSIVE)
:
4:3 OUTPUT:
RGB
(COMPONENT OFF)
VIDEO
FULL
YES
NO
Is this player connected to an amplifier
(receiver) ? Select the type of jack you
are using.
(receiver) ? Select the type of jack you
are using.
LINE OUTPUT L/R (AUDIO)
DIGITAL OUTPUT
AUDIO SETUP
AUDIO DRC:
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
MPEG:
STANDARD
ON
DOWNMIX:
DOLBY SURROUND
DOLBY DIGITAL
DTS:
D-PCM
48kHz/96kHz PCM:
48kHz/16bit
DOLBY DIGITAL
AUDIO SETUP
AUDIO DRC:
DIGITAL OUT:
DOLBY DIGITAL:
MPEG:
MPEG:
STANDARD
ON
DOWNMIX:
DOLBY SURROUND
DOLBY DIGITAL
PCM
DTS:
48kHz/96kHz PCM:
48kHz/96kHz PCM:
OFF
OFF
ON