Sony HVR-1500 Benutzerhandbuch

83

Menu Contents

  

Chap

te

r 7
  

Men

u

s

JOG CONTROL [> Jog ctrl]: Select whether to adjust the 

audio playback speed during slow playback.

This setting is invalid when playing back in HDV format.

OFF [>> OFF]: Do not adjust the audio playback speed.
*

ON [>> ON]: Adjust the audio playback speed.

MUTING IN SHTL [> Shutl mute]: Set the audio muting 

conditions during shuttle playback.

This setting is invalid when playing back in HDV format.

OFF [>> OFF]: Not suppressed.

CUEUP or PREROLL [>> CUEUP]: Suppressed during cue-

up or preroll operations.

FULL [>> FULL]: Suppressed in shuttle mode.

AUDIO EDIT [> Audio edit]: Specify the type of editing for 

audio signals.

This setting is invalid for the HDV format.

CUT EDIT [>> Cut edit]: Cut editing (Discontinuity in audio 

signal may result at the editing point, causing noise during 
playback.)

FADE IN/OUT [>> Fade]: Fade in and fade out

DV PB ATT [> DV PB ATT]: When playing back a tape 

recorded in consumer DV format, select whether to 
attenuate the audio output level.

OFF [>> OFF]: Do not attenuate.
*ON [>> ON]: Attenuate.

This setting is valid only when the recording format setting is 
DVCAM. This is not valid for DV(SP) format.

VIDEO OUTPUT [> Video Out]: Select the format of analog 

video signals to be output from the three VIDEO OUT 
connectors).

*COMPOSITE&S-VIDEO [>> Compst&S]: Set to S-Y, S-C 

output and composite output.

COMPONENT (SD) [>> Compnt SD]: Set to component Y/R-

Y/B-Y (SD) output.

COMPONENT (HD) [>> Compnt HD]: Set to component Y/Pr/

Pb (HD) output.

AUDIO OUTPUT [> Audio Out]: Select the channels for 

audio output from the AUDIO OUT 1/3 and 2/4 
connectors.

1/2 CH [>> 1/2CH]: Output channel 1 to the AUDIO OUT 1/3 

connector and channel 2 to the AUDIO OUT 2/4 connector.

3/4 CH [>> 3/4CH]: Output channel 3 to the AUDIO OUT 1/3 

connector and channel 4 to the AUDIO OUT 2/4 connector.

i.LINK FORMAT [> i.Link Fmt]: Select whether the i.LINK 

output format is automatically determined, or whether it is 
switched according to the i.LINK input selection.

Since the i.LINK stream is different for HDV or DV/DVCAM, 
switching causes a bus reset on the i.LINK interface, which 
may cause a problem with some connected nonlinear editors. 
In such cases, set this item to i.LINK INPUT, and select the 
i.LINK input format to match that to be used.

* AUTO [>> AUTO]: The i.LINK output format is automatically 

determined as follows.
During playback: Switched automatically to DV/DVCAM 

or HDV according to the format in which the tape is 
recorded.

During recording or EE mode: HDV format when the 

i.LINK input is HDV, and DV/DVCAM format when 
another format is selected.

i.LINK INPUT [>> i.Link in]:The i.LINK output format is 

switched as follows, according to the i.LINK input selection.
For DV/DVCAM input selection: Fixed at DV/DVCAM 

format. During HDV tape playback, output converted to 
DV or DVCAM according to the DV recording format. 
(i.LINK OUTPUT menu item setting is invalid).

For HDV input selection: The i.LINK output is always an 

HDV signal.

In this case, DV/DVCAM tape playback is not possible.
For SD input selection other than i.LINK: As for AUTO, 

the playback format is automatically switched to DV/
DVCAM or HDV according to the format recorded on 
the tape, and the setting of the i.LINK OUTPUT menu 
item.

IN

OUT