Sony net md walkman mz-n10 Benutzerhandbuch

15

This set can check if the set and remote commander function nor-
mally.

• Setting method of key check mode
1. Set the test mode (see page 11).
2. Pressing the 

[T MARK]

  key  or 

[DISPLAY]

  key on the remote

commander for several seconds (about 3 seconds) activates the
key check mode. (At the last two digits, AD value of remote com-
mander key line is displayed in hexadecimal)

3. When each key on the set and on remote commander is pressed,

its name is displayed on the remote commander LCD.  (The
operated position is displayed for 4 seconds after the slide
switch is operated. If any other key is pressed during this dis-
play, the remote commander LCD switches to its name dis-
play)

Example1: When the

>

key on the set is pressed:

Example2: When the  

>

key on the remote commander is

pressed:

4. When all the keys on the set and on the remote commander are

considered as OK, the following displays are shown for 4 sec-
onds.

Example1: When the keys on the set are considered as OK:

This set can display the count of errors that occurred during the
recording/playing for checking.

1. Set the test mode (see page 11).
2. Press the

N

key or 

z

REC

. key, and the playing or re-

cording sound skip check result display mode becomes active
respectively and press the 

 >

  key on the remote commander,

and then the playing sound skip check result display mode
becomes active where the LCD displays the following.

3. When the

N

key is pressed, total error count is displayed on

the LCD, and each time the

>

key is pressed, the display item

moves down by one as shown below. Also, if the

.

key  is

pressed, the display item moves up by one, then if the 

z

REC

.

key is pressed, the display in the record mode appears.
When the 

z

REC

. key is pressed, total error count is dis-

played on the LCD, and each time the

>

key is pressed,

the display item moves down by one as shown below. Also, if
the

.

key is pressed, the display item moves up by one,

then if the

N

key is pressed, the display in the play mode

appears.

Cause of error

Description of error

EIB

Sound error correction error

Play

Stat

Decoder status error

Adrs

Address access error

BEmp

Buffer is empty

BOvr

Buffer is full, and sounds were
dumped

Record

Bful

Buffer capacity becomes less,
and forcible writing occurred

Rtry

Retry times over

4. To quit the sound skip check result display mode and to return

to the test mode (display check mode), press the

x

key.

Remote commander LCD display

Total count of play 
system errors (hex.)

Total count of record
system errors (hex.)

P * * R * *

000

000 P * * R * *

000 E I B   * *

000 S t a t * *

000 A d r s * *

000 B E m p * *

000 # # # # # #

000 P * * R * *

000 B O v r * *

000 B f u l * *

000 R t r y * *

000 # # # # # #

P**R**

: Total play/record errors (hex.)

**

: Counter of sound skip check each item (hex.)

######

: 6-digit address where sound was skipped last (hex.)

Playing sound skip
result display

Recording sound skip
result display

Remote commander LCD display

**

: AD value of the remote commander key 

(hexadecimal 00 to FF) 

       **

000

Remote commander LCD display

**

: AD value of the remote commander key 

(hexadecimal 00 to FF) 

FF     **

000

Remote commander LCD display

**

: AD value of the remote commander key 

(hexadecimal 00 to FF) 

rFF  **

000

Remote commander LCD display

Set LCD display

**

: AD value of the remote commander key 

(hexadecimal 00 to FF) 

SET OK **

888

SET OK **

888