Sony SRX-T110 Benutzerhandbuch
11
Location and Function of Controls
Chapt
er 1 Ov
e
rv
ie
w
The setting also functions when you operate this unit with
the Remote Commander.
the Remote Commander.
Remote Commander
• Be sure that there is nothing to obstruct the infrared
beam between the Remote Commander and the
projector. Direct the Remote Commander toward one of
the remote control detectors at the front and rear of the
projector when operating.
projector. Direct the Remote Commander toward one of
the remote control detectors at the front and rear of the
projector when operating.
• The operation range is limited. The shorter the distance
between the Remote Commander and the projector, the
wider the angle within which the Commander can
control the projector.
wider the angle within which the Commander can
control the projector.
a ?/1 (power on/standby) buttons
?: Press to turn on the projector.
1: Press to make the projector enter standby mode.
?: Press to turn on the projector.
1: Press to make the projector enter standby mode.
b SCREEN MODE button
Selects single-, dual- or quad-screen. Each press of the
button changes the mode, 1 (single), 2 (dual) and 4 (quad),
in this order.
Selects single-, dual- or quad-screen. Each press of the
button changes the mode, 1 (single), 2 (dual) and 4 (quad),
in this order.
c MUTING button
Press to cut off the whole picture on the screen. Press it
again to restore the picture. Activating the muting function
shuts off from lamp light completely using a shutter, and
displays the black signal on the whole screen.
Press to cut off the whole picture on the screen. Press it
again to restore the picture. Activating the muting function
shuts off from lamp light completely using a shutter, and
displays the black signal on the whole screen.
d FUNCTION 1/2/3 buttons
Use these buttons in synchronization with the FUNCTION
1, 2 and 3 buttons in the Control Function Menu window
of the SRX Controller. You can recall the data set or
adjusted with the SRX Controller. You cannot recall
settings registered in FUNCTION 4 to 7 buttons.
Use these buttons in synchronization with the FUNCTION
1, 2 and 3 buttons in the Control Function Menu window
of the SRX Controller. You can recall the data set or
adjusted with the SRX Controller. You cannot recall
settings registered in FUNCTION 4 to 7 buttons.
e INPUT SEL (Input select) A/B/C/D buttons
Select the input source you want to project or operate.
A: Selects the signal input from the connectors on the pre-
Select the input source you want to project or operate.
A: Selects the signal input from the connectors on the pre-
installed input board in the INPUT A section.
B: Selects the signal input from the connectors on the
optional input board installed in the INPUT B section.
C: Selects the signal input from the connectors on the
optional input board installed in the INPUT C section.
D: Selects the signal input from the connectors on the
optional input board installed in the INPUT D section.
Use these buttons together with the PICTURE CONT
buttons (6) or SCREEN SEL buttons (7).
Example: When you want to increase the contrast of the
buttons (6) or SCREEN SEL buttons (7).
Example: When you want to increase the contrast of the
signal input from INPUT A, press INPUT SEL A
button, then press the CONTR + button.
button, then press the CONTR + button.
f PICTURE CONT (Picture control) buttons
Adjust the projected picture quality.
CONTR (Contrast) +/–: Adjust the contrast. Pressing the
Adjust the projected picture quality.
CONTR (Contrast) +/–: Adjust the contrast. Pressing the
+ button increases the contrast. Pressing the – button
decreases the contrast.
decreases the contrast.
BRIGHT (Brightness) +/–: Adjust the picture brightness.
Pressing the + button makes the picture brighter.
Pressing the – button makes the picture darker.
Pressing the – button makes the picture darker.
SHARP (Sharpness) +/–: Adjust the picture sharpness.
Pressing the + button makes the picture sharper.
Pressing the – button makes the picture softer.
Pressing the – button makes the picture softer.
In dual- or quad-screen mode, adjustment can be made for
the input signal from each input board.
Select the input signal with the INPUT SEL A/B/C/D
buttons (5), then adjust the picture with these buttons. In
single-screen mode, you need not press the INPUT SEL
button.
Example: When you want to increase the contrast for the
the input signal from each input board.
Select the input signal with the INPUT SEL A/B/C/D
buttons (5), then adjust the picture with these buttons. In
single-screen mode, you need not press the INPUT SEL
button.
Example: When you want to increase the contrast for the
signal input from INPUT A, press the INPUT SEL A
button, then press the CONTR + button.
button, then press the CONTR + button.
g SCREEN SEL (Screen select) buttons
In the dual-screen mode or quad-screen mode, select one
of the divided screens where you want to project the
selected signal from each input.
In the dual-screen mode or quad-screen mode, select one
of the divided screens where you want to project the
selected signal from each input.
Notes
SR Projector
RM-PJ4K
IR
I
1
SCREEN
MODE
MODE
1 2 4
MUTING
FUNCTION
INPUT SEL
A
1
1
2
3
2
3
4
B
C
D
PICTURE CONT
BRIGHT
CONTR
+
–
+
–
+
–
+
–
+
–
+
–
SHARP
ZOOM
FOCUS
SHIFT
SCREEN SEL
LENS CONT
1
2
3
4
5
7
6
8