Panasonic nv-gs8eb Benutzerhandbuch
Before Use
-10-
≥Make sure to match the poles correctly when
inserting the battery.
ª Using the Remote Controller
1
1
Direct the Remote Controller at the Remote
Control Sensor
Control Sensor
(31)
of the Movie Camera
and press an appropriate button.
≥Distance from the Movie Camera: Within
approximately 5 metres
≥Angle: Within approximately 15o in the
vertical and horizontal directions from the
central axis
central axis
≥The above operating ranges are for indoor use.
Outdoors or under strong light, the Movie
Camera may not operate properly even within
the above ranges.
Camera may not operate properly even within
the above ranges.
Selecting Remote Controller Modes
When 2 Movie Cameras are used
simultaneously, they can be operated individually
by selecting different Remote Controller Modes.
≥If the Remote Controller Mode of the Movie
When 2 Movie Cameras are used
simultaneously, they can be operated individually
by selecting different Remote Controller Modes.
≥If the Remote Controller Mode of the Movie
Camera and that of the Remote Controller do
not match, [REMOTE] Indication is displayed.
not match, [REMOTE] Indication is displayed.
WARNING
“THE LITHIUM BATTERY IS A CRITICAL
COMPONENT (TYPE NUMBER CR2025
MANUFACTURED BY PANASONIC).
IT MUST NEVER BE SUBJECTED TO
EXCESSIVE HEAT OR DISCHARGE. IT
MUST THEREFORE ONLY BE FITTED IN
EQUIPMENT DESIGNED SPECIFICALLY
FOR ITS USE.
REPLACEMENT BATTERIES MUST BE OF
THE SAME TYPE AND MANUFACTURER.
THEY MUST BE FITTED IN THE SAME
MANNER AND LOCATION AS THE
ORIGINAL BATTERY, WITH THE
CORRECT POLARITY CONNECTIONS
OBSERVED.
DO NOT ATTEMPT TO RE-CHARGE THE
OLD BATTERY OR RE-USE IT FOR ANY
OTHER PURPOSE. IT SHOULD BE
DISPOSED OF IN WASTE PRODUCTS
DESTINED FOR BURIAL RATHER THAN
INCINERATION.”
“THE LITHIUM BATTERY IS A CRITICAL
COMPONENT (TYPE NUMBER CR2025
MANUFACTURED BY PANASONIC).
IT MUST NEVER BE SUBJECTED TO
EXCESSIVE HEAT OR DISCHARGE. IT
MUST THEREFORE ONLY BE FITTED IN
EQUIPMENT DESIGNED SPECIFICALLY
FOR ITS USE.
REPLACEMENT BATTERIES MUST BE OF
THE SAME TYPE AND MANUFACTURER.
THEY MUST BE FITTED IN THE SAME
MANNER AND LOCATION AS THE
ORIGINAL BATTERY, WITH THE
CORRECT POLARITY CONNECTIONS
OBSERVED.
DO NOT ATTEMPT TO RE-CHARGE THE
OLD BATTERY OR RE-USE IT FOR ANY
OTHER PURPOSE. IT SHOULD BE
DISPOSED OF IN WASTE PRODUCTS
DESTINED FOR BURIAL RATHER THAN
INCINERATION.”
15˚
15˚
15˚
15˚
(31)
Setup on the Movie Camera:
Set [REMOTE] on the [INITIAL] Sub-Menu to the
desired Remote Controller Mode. (
Set [REMOTE] on the [INITIAL] Sub-Menu to the
desired Remote Controller Mode. (
-17-
)
Setup on the Remote Controller:
[VCR1]:
Press the [
D] Button and [∫] Button
simultaneously.
1
[VCR2]:
Press the [
E] Button and [∫] Button
simultaneously.
2
≥When the battery in the Remote Controller is
replaced, the mode is automatically reset to
[VCR1] Mode.
[VCR1] Mode.
Power Supply
ª Using the AC Adaptor
1
Connect the DC Input Lead to the
[DC/C.C.IN] Socket on the Movie Camera.
[DC/C.C.IN] Socket on the Movie Camera.
2
Connect the DC Input Lead to the AC
Adaptor.
Adaptor.
3
Connect the AC Mains Lead to the AC
Adaptor and the AC mains socket.
≥The AC Mains Lead’s outlet plug does not fit
Adaptor and the AC mains socket.
≥The AC Mains Lead’s outlet plug does not fit
entirely into the AC Adaptor socket. A gap will
remain as shown
remain as shown
1.
≥Before connecting or disconnecting the
power supply, set the [OFF/ON] Switch on
the Movie Camera to [OFF] and make sure
that Power Lamp is not lit.
the Movie Camera to [OFF] and make sure
that Power Lamp is not lit.
INDEX
INDEX
SELECT
STOP
K
L
∫
STILL ADV
T
W
PAUSE STILL ADV
6
1
5
;
E
D
P.B. ZOOM
2
1
1
1
2
3
15B-ENG.book 10 ページ ２００４年２月２日 月曜日 午後４時４５分