Panasonic nv-mx500 Benutzerhandbuch

Seite von 27
VCR Mode
-29-
Audio Dubbing
You can add music or narration to the recorded Cassette.
≥If the tape recorded in the [16bit] Mode is dubbed with the 
Audio Dubbing function, the original sound is erased. (If 
you wish to preserve the original sound, use the [12bit] 
Mode when recording.)
≥Audio Dubbing cannot be performed on a recording done in 
LP Mode. (
-14-
)
1
Set [VCR FUNCTIONS] >> [AV IN/OUT SETUP] >> 
[AV JACK] >> [IN/OUT].
2
Continuing the aforesaid setup, select [A.DUB INPUT] 
>> [MIC] or [AV IN].
≥Set to [AV IN] when external device is used, and to [MIC] 
when an external or built-in microphone is used.
≥Switch the Movie Camera over to the Still Playback 
Mode where you want to add new sound.
3
Press the [A.DUB] Button 
(64)
 on the Remote 
Controller.
4
To start Audio Dubbing, press the [
;] Button 
(80)
 on 
the Remote Controller.
To Cancel Audio Dubbing
Press the [
;] Button 
(80)
 on the Remote Controller.
The Movie Camera is in the Still Playback Mode again.
To dub audio while listening to a pre-recorded sound
When pausing the audio dubbing, [12bit AUDIO] on the 
[PLAYBACK FUNCTIONS] Sub-Menu is automatically set to 
[ST2] and you can check the pre-recorded sound. When a 
microphone is used for audio dubbing, use headphones to 
listen to the pre-recorded sound while dubbing the audio. 
(When using headphones, set [AV JACK] on the 
[AV IN/OUT SETUP] Sub-Menu to [OUT/PHONES].) When 
the line input is used, you can dub audio while listening to a 
pre-recorded sound from the speaker.
To Play Back the Sound Recorded by 12bit Audio 
Dubbing
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> 
[12bit AUDIO] >> [ST2] or [MIX].
ST1: It plays back only the original sound.
ST2: It plays back only the sound added by Audio Dubbing.
MIX: It plays back both the original sound and the sound 
added by Audio Dubbing simultaneously.
≥For other notes concerning this item, see 
-46-
.
Audio Level Adjustment
You can adjust the Audio Level for audio dubbing by 
selecting a desired setting for [AUDIO LEVEL] on the 
[RECORDING SETUP] Sub-Menu of the 
[VCR FUNCTIONS] Main-Menu.
(26)
(51)
M E N U
PUSH
SHUTTER/IRIS/
VOL/JOG
INDEX
INDEX
SELECT
STOP
K
L
V
/REW
STILL ADV
T
W
s
VO
L
r
¥REC
MULTI/
P-IN-P
A.DUB
PLAY
PAUSE
FF/
W
STILL ADV
6
1
5
;
E
D
(64)
(80)
When you set [MODE] of [AUDIO LEVEL] to any other 
setting than [AUTO], the Audio Level Indication appears. 
Adjust the [GAIN] value.
When this setting is changed, the [MIC LEVEL ADJ.] setting 
on the [ADVANCED FUNCTIONS] Sub-Menu of the 
[CAMERA FUNCTIONS] Main-Menu will likewise be 
changed.
For details, refer to Microphone Sensitivity Level Adjustment 
(
-21-
).
To Reduce the Sound Distortion
Lower the output level of the external audio device. Or, set 
the [MODE] of [AUDIO LEVEL] to [AUTO] or [MNL(AGC)].
Copying on an S-VHS (or a VHS) Cassette
(Dubbing)
After connecting the Movie Camera and the VCR as 
illustrated, start the following procedures.
1 AV Cable
2 S-Video Cable (not supplied)
≥If your TV is not equipped with AV Input Sockets, the 21-pin 
Adaptor (purchase separately) is necessary. Consult your 
dealer.
≥Be sure to press the [OSD] Button (
-6-
) on the Remote 
Controller prior to copying so that no indications are visible. 
Otherwise, the displayed tape counter and function 
indications are also copied.
Movie Camera:
1
Insert the recorded Cassette.
VCR:
2
Insert an unrecorded Cassette with an erasure 
prevention tab.
≥If various setups (such as external input, tape speed, 
etc.) are required, please refer to the operating 
instructions of your VCR.
Movie Camera:
3
Press the [
1] Button to start playback.
VCR:
4
Start recording.
5
Press the Pause or Stop Button to stop recording.
AUDIO LEVEL SETUP
PRESS MENU TO RETURN
MODE AUTO  MNL    MNL 
         (AGC)  (NO-AGC)
(dB) -30         0  +6 
|||||||||-----
GAIN
21-pin Adaptor
MIC
AV IN/OUT 
PHONES/REMOTE
USB/ 
EDIT
D(MINI)
S-VIDEO
IN/OUT
1
2
[VIDEO IN]
[AUDIO IN]
[S-VIDEO IN]
B5-B.book  29 ページ  2002年8月6日 火曜日 午前11時33分