Panasonic nvgs300gct Benutzerhandbuch
Before using
13
VQT0W28
Quick Start
When quick start is ON the battery power is still
being consumed, even when the LCD monitor
and the viewfinder are closed.
The movie camera will resume recording/pause
mode about 1.7 seconds after the LCD monitor or
the viewfinder is reopended.
≥Please note in quick start mode approximately
being consumed, even when the LCD monitor
and the viewfinder are closed.
The movie camera will resume recording/pause
mode about 1.7 seconds after the LCD monitor or
the viewfinder is reopended.
≥Please note in quick start mode approximately
half the pause recording power is being
consumed. Using quick start mode will reduce
the battery recording/playback time.
consumed. Using quick start mode will reduce
the battery recording/playback time.
≥This is only activated in the following cases.
≥A tape or a card is inserted, while the Tape
Recording Mode is set.
≥A card is inserted, while the Card Recording
Mode is set.
≥Set to Tape/Card Recording Mode.
1
Set [SETUP] >> [QUICK START] >> [ON].
(
(
-18-
)
2
While the [OFF/ON] switch is still set to
[ON], close the LCD monitor and retract the
viewfinder.
[ON], close the LCD monitor and retract the
viewfinder.
≥The Status indicator lights green and the unit
goes into quick start standby mode.
≥The lens cover does not close.
≥The movie camera will not go into quick start
≥The movie camera will not go into quick start
standby mode unless the LCD monitor is
closed and the viewfinder is retracted.
closed and the viewfinder is retracted.
3
Open the LCD monitor or extend the
Viewfinder.
Viewfinder.
≥The Status indicator lights red and the
camera is put into recording pause approx.
1.7 seconds after it is turned on.
1.7 seconds after it is turned on.
ª
To cancel Quick Start
1
Set [SETUP] >> [QUICK START] >> [OFF].
(
(
-18-
)
≥If the [OFF/ON] switch is set to [OFF] while the
unit is in quick start standby mode, the lens
cover closes and the power turns off.
cover closes and the power turns off.
≥If the standby continues for approx. 30 minutes,
then the Status indicator will go off and the
camera will be completely turned off.
camera will be completely turned off.
≥If the Mode dial is moved or the battery is
removed in quick start standby mode, quick
start is cancelled and the power turns off.
start is cancelled and the power turns off.
≥When the movie camera is quick-started with
the white balance on automatic, it may take
some time until the white balance is adjusted if
the scene being recorded has a light source
different from the scene last recorded. (When
the colour night view function is used, however,
the white balance of the scene last recorded is
retained.)
some time until the white balance is adjusted if
the scene being recorded has a light source
different from the scene last recorded. (When
the colour night view function is used, however,
the white balance of the scene last recorded is
retained.)
≥If the power is turned on in quick start standby
mode, the zoom magnification becomes 1
k and
the picture size may differ from what it was
before quick start standby mode.
before quick start standby mode.
≥If [POWER SAVE] (
-52-
) is set to [5 MINUTES]
and the unit automatically goes into quick start
standby mode, set the [OFF/ON] switch to
[OFF], then to [ON] again. Also, close the LCD
monitor and retract the viewfinder and then
open the LCD monitor or extend the viewfinder
again.
standby mode, set the [OFF/ON] switch to
[OFF], then to [ON] again. Also, close the LCD
monitor and retract the viewfinder and then
open the LCD monitor or extend the viewfinder
again.
≥When using the AC adaptor, Quick Start can be
used even if a tape/card is not inserted.
OFF
ON
OFF
ON