Panasonic pv-v4522 Benutzerhandbuch

VCR fast forwards (skips) over 1~3 minutes
of recorded tape.

• Press CM/ZERO repeatedly to change

skip time as shown below.

• No indication appears.

    PLAY

1st  Press

2nd Press

3rd  Press

1 min Skip

2 min Skip

3 min Skip

Set to playback a recording over and over.

ON : Play repeats at

tape end or if
unrecorded portion
over 30 sec. is
detected.

VCR         CLOCK     CHANNEL

SELECT   :            SET : 
EXIT        : ACT I ON     

REPEAT  PLAY             :OFF

REMOTE WARNING     :ON
AUTO  SHUT- OFF       :OFF
IDIOMA/LANGUE : ENGLISH
VCR’ S  OUTPUT CH    :3

Press 
to select REPEAT PLAY
and press   to set ON
or OFF.

To quickly return to a specified tape location.

• Unit will go into FF or

REW mode and stop at
the last point the
Counter was set to
0:00:00.

Press RESET
COUNTER at desired
position to reset to
“0:00:00”.

Press CM/ZERO in Stop
mode to start ZERO
SEARCH.

Press ACTION to display menu.

Press ACTION to return to normal screen.

Press DISPLAY during play
to display Counter.

Continue to record, playback, etc.

Press STOP.

Press CM/ZERO in Play mode.

- 7 -

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

PLAY       1 2 : 0 0AM

 0 : 0 0 : 0 0 

SP

REW        1 2 : 3 0AM          CH  02

 0 : 30 : 30 

SP

STOP       1 2 : 3 1AM          CH  02

 0 : 0 0 : 0 0 

SP

To go to rec. 2 from rec. 4, enter 3 and press
REW.

To go to rec. 6 from rec. 2, enter 4 and press
FF.

NOTE:   indicates start points of each recording.

• If Index Search is started very close to an

index mark, that index mark may not be
counted in the search.

For each recording, an invisible index mark is placed on the tape. A program index and
information are also included for timer recordings. These marks are used to access or
scan recordings.

Locates end point of recording for continuity.

Examples of Program End Search.

If search
exceeds a few
seconds in
BLANK area.

➛ search continues 7 sec. past end point,

➛ tape rewinds to 10 sec. before end point,

➛ tape plays to end point and stops.

• If Program End Search is started very

close to an index mark, that mark may be
skipped over.

• To cancel, press PLAY or STOP.

Press SEARCH* to
display SEARCH in Stop
or Play mode, and then
press NUMBER keys to
select recording
number.

• To calculate number,

see below.

Press FF or REW on
the remote to start
search.

Press FF on the remote
to start PROGRAM
END SEARCH.

Play begins at search
end. To search forward
or back 1 index, press
FF or REW on the
remote or VCR while
screen left is displayed
(10 sec.).

Program  2

Program 1 

the current tape position 
Press SEARCH button

BLANK

INDEX

Press SEARCH twice to display SEARCH
in Stop or Play mode.

Program 2 or BLANK

Program 1 

the current tape position 
Press SEARCH button

INDEX

Program  2

Program 1 

the current tape position 
Press SEARCH button

INDEX

INDEX

 BLANK

 BLANK

- 6 -

• To cancel, press

PLAY or STOP.

• To cancel, press

PLAY or STOP.

                   SEARCH
      INDEX          PROGRAM END

ENTER   INDEX  NUMBER  :1
USING   1- 9 KEYS

FORWARD  SEARCH  :FF
REVERSE  SEARCH  :REW
NEXT     :SEARCH
EXIT     :STOP

           INDEX  SEARCH

FORWARD  SEARCH  :FF
REVERSE  SEARCH  :REW

                   SEARCH
      INDEX          PROGRAM END

SEARCH START  :FF

EXIT     :SEARCH

• Arrow indicates selection.

STEREO
SAP
MONO

H I F I : L / R
H I F I : L 
H I F I : R
NORMAL

• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound.

Standard stereo tapes will playback in monaural sound.

• To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to

a stereo TV or an external stereo amp and speakers. (See page 4.)

• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
• Hi-Fi and normal audio playback volume level may differ.

• Refer to “Receivable

Broadcast Types” on page 4.

• Select “HIFI(L/R)” or

“HIFI(L)” or “HIFI(R)” to
listen to stereo recordings in
stereo sound.
Select “NORMAL” for
monaural sound.

Press SAP/ Hi-Fi repeatedly
to select desired mode.

Press SAP/ Hi-Fi repeatedly
to select desired mode.

Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)

Do a recording.
See p. 5 of “Basic Operations” Instruction book.

Start playback.
See p. 5 of “Basic Operations” Instruction book.

Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)

• Arrow indicates

selection.

- 5 -

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Normal monaural sound broadcast.

Secondary Audio Program (sub language) broadcast.
Select SAP audio mode for the sub language.

Multi-channel Television Sound Stereo broadcast.
Select STEREO audio mode.

• If stereo broadcast is weak and display flickers, select

MONO audio mode for possibly better results.

Multi-channel Television Sound Stereo (main language)
and Secondary Audio Program (sub language)
broadcasts are being received simultaneously.
Select STEREO or SAP audio mode.

The following are possible audio broadcast types and on-screen displays.
The signal being received is indicated with an “ ” mark while the selected audio mode is
indicated with an arrow.

To display the broadcast signal being received,
➛

➛

➛

➛

➛ press DISPLAY*.

Equipped with 

-TV Noise Reduction for true

MTS reproduction. 

-TV Noise Reduction is

required for good stereo separation and audio
fidelity. 

 is a registered trademark, and is

licensed by 

 Technology Licensing.

Make the Audio/Video Connection as shown on page 3.
• You can use a TV connected to Stereo amp and speakers instead of a Stereo TV.

Stereo Amplifier

AUDIO IN

R

L

VCR

R
L

R

OUT TO TV

VHF/UHF

TV

R
L

AUDIO OUT

- 4 -

STOP       1 2 : 0 0AM

CH  02   

0 : 0 0 : 0 0 

SP

STEREO
SAP
MONO

STOP       1 2 : 0 0AM

CH  02   

0 : 0 0 : 0 0 

SP

STEREO
SAP
MONO

STOP       1 2 : 0 0AM

CH  02   

0 : 0 0 : 0 0 

SP

STEREO
SAP
MONO

STOP       1 2 : 0 0AM

CH  02   

0 : 0 0 : 0 0 

SP

STEREO
SAP
MONO

You Cannot

You Can

• record and

view both
scrambled and
unscrambled
channels if
additional
equipment is
added. This
connection
requires: two
converter
boxes, an A/B
switch, and a
2-way splitter.

• view channel

other than
the one
selected for
any type of
recording.

• do a Timer

recording of
a channel
unless you
select it at
the cable
box.

If your TV has AUDIO IN and VIDEO IN terminals, you can connect your VCR
to them to receive higher quality picture and sound.

Connect the VCR’s VIDEO OUT jack to the TV’s VIDEO IN jack.

PV-V4522 : Connect VCR’s L/R AUDIO OUT jacks to the TV’s L/R

AUDIO IN jacks.

Set the VIDEO/TV selector of your TV (Monitor/Receiver) to “VIDEO.”

IN

VIDEO

AUDIO

R

L

OUT

 AUDIO

IN 1

 R

 L

 VIDEO

OUT

TV

IN 2

IN 1

CABLE BOX

OUT

IN

OUT 2

OUT 1

2-Way Splitter

CABLE BOX

OUT

A/B Switch

VCR

IN

VHF/UHF

■

■

■

■

■

      

VCR

 AUDIO

IN 1

 R

 L

 VIDEO

OUT

CABLE BOX

OUT

IN

IN

R

L

OUT

TV

VIDEO

AUDIO

VHF/UHF

■ 

■ 

■ 

■ 

■  With a Cable Box (VCR         Cable Box)

You Cannot

You Can

• record

scrambled
channels.

• view any

(including
scrambled)
channel.

• use VCR

Remote
Control to
select
channels
without using
Multi-brand
control feature.

PV-V4022 : Connect VCR’s AUDIO OUT jack to the TV’s AUDIO IN

jack.

TV

VCR

IN FROM ANT.

OUT TO TV

VHF/UHF

VIDEO IN

R

L

AUDIO IN

L

R

VIDEO OUT

AUDIO OUT

R

TV

VCR

IN FROM ANT.

OUT TO TV

VHF/UHF

VIDEO IN

R

VIDEO  OUT

AUDIO IN

AUDIO OUT

1

2

3

- 3 -

The Remote Control can be set to control some TV functions.

Mode

Unit

VCR

TV

VCR

TV

All

VOL UP/DOWN

POWER, INPUT, ENTER,
NUMBER keys, CH UP/DOWN,
VOL UP/DOWN

VCR/TV, PLAY, STOP, EJECT, SAP/Hi-Fi (PV-V4522
only), DISPLAY, FF, REW, PAUSE/SLOW, REC,
SPEED, CM/ZERO, RESET COUNTER, TAPE POSITION

After remote is set up, you can select VCR or TV for the desired function.

Press VCR or TV on the remote.
(Table below shows available unit buttons for each mode.)

• Not all functions listed may be controllable.

• In TV mode, it may be necessary to press ENTER after pressing NUMBER keys for channel

selection.

➛ hold down TV button,

➛ enter code with NUMBER keys.

• Repeat setup after remote battery replacement.

• Remote will not control every TV made by the manufacturer listed. If you get no

response, your particular unit cannot be controlled. There are NO additional codes for
the products listed. If your product is not listed, then the remote is not compatible with
that product.

➛ press POWER to turn your TV on or off.
• See table below for controllable functions in each mode.

Panasonic ....................... 01, 02
Quasar ............................ 01, 02
RCA ...................................... 03
GE ......................................... 03
Zenith .................................... 04
Magnavox .............................. 05

Sylvania ................................. 05
Sharp ............................... 06, 07
Sony ...................................... 08
Toshiba ................................. 09
Sanyo .................................... 10
Fisher .................................... 10

JVC ....................................... 11
Hitachi ................................... 12
Mitsubishi ........................ 07, 13
Samsung ............................... 14
Gold Star ................... 15, 16, 17

• Due to changes in infra-red commands used by manufacturers, some brands have several codes.

If your unit does not respond to the first code, please try the next one.

• Some TV brands require you to turn on the power manually.

- 2 -

V4022-4522 Advanced-2 (02-5-9) 2nd.p65

2002/05/09, 16:29

3