Panasonic sa-ht680 Benutzerhandbuch
24
RQT7969
The
r
a
dio
The radio
Up to 15 stations can be set in each band, FM and AM.
1
Press [SELECTOR] to select “FM” or “AM”.
2
Press [TUNE MODE] to select “MANUAL”.
Each time you press the button: MANUAL
()PRESET
3
Press [
X TUNING W] to tune to the lowest
frequency (FM: 87.9 or 87.5, AM: 520).
4
Press and hold [MEMORY].
Release the button when “FM AUTO” or “AM AUTO” is
displayed.
displayed.
The tuner presets all the stations it can receive into the
channels in ascending order.
≥“SET OK” is displayed when the stations are set, and the
channels in ascending order.
≥“SET OK” is displayed when the stations are set, and the
radio tunes to the last preset station.
≥“ERROR” is displayed when automatic presetting is
unsuccessful. Preset the channels manually (
➜ below).
1
Press [SELECTOR] to select “FM” or
“AM”.
2
Press [TUNE MODE] to select “MANUAL”.
3
Press [
X TUNING W] to select the
frequency.
Press and hold
[
X
TUNING
W] until the frequency starts
scrolling to start automatic tuning. Tuning stops when a station
is found.
is found.
∫ Presetting the channel
Up to 15 stations can be set in each band, FM and AM.
1
While listening to the radio broadcast
Press [ENTER].
2
While the frequency and “
PGM
” are flashing on the display
Press the numbered buttons to select a channel.
Alternatively, press [
W CH X], then press [ENTER].
≥To select a 2-digit number
e.g. 12: [
S10]
➜ [1] ➜ [2].
The station occupying a channel is erased if another station is preset
to that channel.
to that channel.
1
Press [TUNER/BAND] to select “FM” or
“AM”.
2
Press the numbered buttons to select the
channel.
Alternatively, press
[
W
CH
X]
To select a 2-digit number
e.g. 12: [
e.g. 12: [
S10]
➜ [1] ➜ [2]
When a stereo FM broadcast is being received.
∫ If noise is excessive in FM
Press [FM MODE] to display “MONO”.
Press [FM MODE] again to cancel the mode.
The mode is also canceled when you change the frequency.
The mode is also canceled when you change the frequency.
∫ FM frequency step
You can change the FM step. The step is factory-set to 0.2 MHz, but
you can change it to receive broadcasts allocated in 0.1-MHz steps.
you can change it to receive broadcasts allocated in 0.1-MHz steps.
1 Press [SELECTOR] to select “FM”.
2 Press and hold [SELECTOR].
2 Press and hold [SELECTOR].
After a few seconds the display changes to show the current
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
To return to the original step, repeat the above steps.
[Note]
Any FM/AM frequencies preset in channels will be changed by this
procedure. Preset them again.
procedure. Preset them again.
Automatic presetting
Manual tuning
1
2
3
4
5
OPEN CLOSE DISC CHANGE
DISC CHECK
SELECTOR
TUNE MODE
FM MODE
MEMORY
PROGRESSIVE CD MODE
DISC
POWER
DOWN
UP
PHONES
VOLUME
AC IN
TUNING
SELECTOR
TUNING
TUNE MODE
MEMORY
FM MODE
M
ain unit only
M
ain unit only
Selecting the preset channels
VOLUME
CH
SKIP
SLOW/SEARCH
MENU
DIRECT
NAVIGATOR
TOP MENU
RETURN
FUNCTIONS
VCR
TV
TUNER/BAND
DISC
ENTER
AV SYSTEM
DVD/CD
PLAY
LIST
TV VOL
TV VOL
ENTER
1
2
6
9
4
5
7
8
CANCEL
0
510
3
TV/VIDEO
AUX
ENTER
TUNER/BAND
CH
Numbered
buttons
TUNED ST
M
ain unit only
TUNED
MONO
M
ain unit only
7969en-p03-26.fm Page 24 Friday, December 17, 2004 11:59 AM