Panasonic SC-HT733 Benutzerhandbuch
4
RQT7972
Simple setup
Preparation
≥To prevent damage or scratches, lay down a soft cloth and perform assembly on it.
≥For assembly, use a Phillips-head screwdriver.
≥Make sure you have all the indicated components before starting assembly, setup, and connection.
≥There is no difference between the right and left speakers and pipes.
≥To prevent damage or scratches, lay down a soft cloth and perform assembly on it.
≥For assembly, use a Phillips-head screwdriver.
≥Make sure you have all the indicated components before starting assembly, setup, and connection.
≥There is no difference between the right and left speakers and pipes.
[HT730]
[HT733]
You can use the front speakers without assembling with the stands. In this case, attach the included
rubber pads to the base of the speakers. This prevents vibration from causing the speakers to move
or fall over. Use 3 or 4 pads per speaker.
rubber pads to the base of the speakers. This prevents vibration from causing the speakers to move
or fall over. Use 3 or 4 pads per speaker.
1
Attach the pipes to the bases.
1
Insert pipe B.
2
Secure pipe B to the base.
Ensure the screws are securely fastened.
Ensure the screws are securely fastened.
2
Assemble the pipes.
1
Thread the speaker cable from pipe A through pipe B and
the base.
For quicker threading, loosely fold the cable in half (do not
crease), pass the folded portion through the pipe, and then pull
the rest of the cable through the base.
the base.
For quicker threading, loosely fold the cable in half (do not
crease), pass the folded portion through the pipe, and then pull
the rest of the cable through the base.
2
Join pipe A to pipe B.
3
Secure the pipes.
Ensure the screws are securely fastened.
Ensure the screws are securely fastened.
3
Attach the pipes to the speakers.
Slot the screw head in between the 2 stoppers of the speaker
groove.
Ensure the pipe is fastened on straight by gradually tightening the
right and left screws alternately until fully tightened.
To prevent a short-circuit, do not cover the connection
terminals with the pipe.
groove.
Ensure the pipe is fastened on straight by gradually tightening the
right and left screws alternately until fully tightened.
To prevent a short-circuit, do not cover the connection
terminals with the pipe.
4
Connect the speaker cables.
5
Secure the speaker cables to the bases.
STEP
1
Front speaker assembly
The supplied stands are specially designed for
attachment to Panasonic SB-FS730 or SB-FS930
front speakers. Use only as indicated in this setup.
attachment to Panasonic SB-FS730 or SB-FS930
front speakers. Use only as indicated in this setup.
2 Front
speakers
speakers
2 Bases
≥2kpipe A
(with cable)
≥2kpipe B
4 Pipes
4 Washer
screws
screws
4 Small
screws
screws
4 Bracket
screws
screws
2 Brackets
Sheet of
rubber pads
rubber pads
Match these holes when you
insert the pipe.
insert the pipe.
Base
Pipe B
Washer screws
Phillips-head screwdriver
(not included)
(not included)
Cable
Pipe B
Cable
Pipe A
Pipe B
Small screws
Pipe A
Pipe B
Bracket screws
Front speaker
Connection terminals
Bracket
Pipe A
Stoppers
Screw head
Rear of the speaker
Twist off the vinyl ends of the
speaker cables.
speaker cables.
_:
White
`:
Blue
Push!
Bottom of the base
2
Press the
speaker cable
against the base
while threading
it between the
pegs.
speaker cable
against the base
while threading
it between the
pegs.
Cable
1
Press the speaker
cable into the base
cover groove as far
as possible.
cable into the base
cover groove as far
as possible.
F
ron
t spe
a
k
e
r as
semb
ly
HT730.book Page 4 Wednesday, January 26, 2005 7:51 PM