Panasonic sl-sw880 Benutzerhandbuch
Using the unit with a car audio
system
system
SL-SW861C comes with a car adaptor and car stereo
cassette adaptor.
cassette adaptor.
Items to be purchased
(SL-SW880/SL-SW860)
(SL-SW880/SL-SW860)
For connection to the car audio system:
Car stereo cassette adaptor (SH-CDM10A)
For securing the unit and connecting the
power supply:
power supply:
≥
Car adaptor (SH-CDC9)
≥
Car mounting kit (SH-CDF20)
Note
.
It may not be possible to use the unit with some types of
car stereo owing to restrictions imposed by the con-
struction of the car stereo cassette adaptor.
car stereo owing to restrictions imposed by the con-
struction of the car stereo cassette adaptor.
For further details, refer to the instructions of the part
concerned.
concerned.
Anti-shock works by reading audio data and storing it in
memory (up to 40 seconds worth). The unit then fills in
interruptions caused by bumps and vibrations with data
from the memory. This unit also incorporates a powerful
anti-shock mechanism that prevents skipping caused
when play speed is changed by swinging of the unit.
memory (up to 40 seconds worth). The unit then fills in
interruptions caused by bumps and vibrations with data
from the memory. This unit also incorporates a powerful
anti-shock mechanism that prevents skipping caused
when play speed is changed by swinging of the unit.
Press during play or stop mode.
The following indicator appears on the display panel.
Note
!
Wait until the jogger indicator appears before starting to
jog.
jog.
When bumps continue repeatedly
The message “SORRY” appears on the display and
sound is interrupted.
sound is interrupted.
The jogger indicator can also flash or go out under
the following conditions:
the following conditions:
≥
As the end of the last track approaches.
≥
As the end of a track approaches during random play, pro-
gram play, and 1 track repeat play.
gram play, and 1 track repeat play.
≥
If the track in play or next track is extremely short.
To cancel the anti-shock function
Press [A.SHOCK] again.
Note
!
≥
The anti-shock setting can be changed during play,
but this may cause a slight interruption in the sound
because the disc’s rotational speed changes.
but this may cause a slight interruption in the sound
because the disc’s rotational speed changes.
≥
During anti-shock operation, the disc rotates at a high-
er rate than usual in collecting extra audio data. This
could result in a slight increase in disc rotation noise.
er rate than usual in collecting extra audio data. This
could result in a slight increase in disc rotation noise.
Listening to sound with the unit con-
nected to an audio system
nected to an audio system
The anti-shock function uses digital signal compression
technology. It is recommended that the anti-shock func-
tion be canceled if the unit is connected to a home
audio system.
technology. It is recommended that the anti-shock func-
tion be canceled if the unit is connected to a home
audio system.
Skipping
tracks
Seaching
through tracks
To adjust the
volume
A.SHOCK
A.SHOCK
A.SHOCK
5
Using the Unit with Optional Accessories
Using the unit with an audio system
Using a stereo connection cable (not included), you can
listen to CDs through your audio system.
listen to CDs through your audio system.
≥
Connect the cable to the amplifier after turning off its
power.
power.
≥
Do not connect the cable to the PHONO jacks on the
amplifier.
amplifier.
≥
Obtain the optional connecting cable if the amplifier
comes with mini-phone jacks.
comes with mini-phone jacks.
≥
Adjust the volume level on the amplifier.
You can connect speakers, active or otherwise, with an
impedance of 1k
impedance of 1k
≠
or less to the headphone jack. Set
the unit’s volume between 5 and 8.
Note
.
Sound quality changes when S-XBS or VMSS
(SL-SW880 only) is selected, but volume is reduced
by approximately fifty percent.
(SL-SW880 only) is selected, but volume is reduced
by approximately fifty percent.
L
R
OUT jack
Stereo connection cable (not included)
To CD or AUX
terminals
terminals
(White)
(Red)
Side panel of the unit
Amplifier
Connect the car stereo cassette adaptor
to the unit’s headphone jack.
(When doing this, keep the unit’s VOLUME
control at a setting between 5 and 8.)
to the unit’s headphone jack.
(When doing this, keep the unit’s VOLUME
control at a setting between 5 and 8.)
RQT5528
Maintaining the
Lens
Lens
Open the lid and clean the lens as shown in the figure.
Use a cotton swab to gently wipe off any finger-prints.
Recommended product: Lens cleaner kit (SZZP1038C)
Use a cotton swab to gently wipe off any finger-prints.
Recommended product: Lens cleaner kit (SZZP1038C)
Lens
Lens
Air blower for
camera lens
camera lens
Anti-Shock Function
Using Stereo Headphones with Remote Control
SL-SW880 ONLY
To start play
To stop play
To turn off
the unit
The remote control can be operated regardless of the
HOLD mode of the unit.
HOLD mode of the unit.
Preparation: Release the remote control from the
HOLD mode.
HOLD mode.
∫
Operation confirmation tones
When an operation button is pressed, a confirmation
tone sounds. Refer to the parentheses in the illustra-
tion for the different types of confirmation tones.
tone sounds. Refer to the parentheses in the illustra-
tion for the different types of confirmation tones.
How to use the remote control
Press once during off or stop mode.
Press once during play.
Press and hold during play or stop mode.
Press once during play.
Press and hold during play.
[VOL] on the remote control adjusts volume
only. To adjust the VMSS effect, use
[VOLUME] on the main unit.
only. To adjust the VMSS effect, use
[VOLUME] on the main unit.
VOL
HOLD
HOLD
VOL
HOLD
VOL
HOLD
VOL
HOLD
VOL
HOLD
VOL
HOLD
G
A.SHOCK
After about
20 seconds
20 seconds
A.SHOCK
Play/stop/off button
[
i
]
[
j
]
[VOL]
About
5 seconds later
5 seconds later
The jogger indicator
starts flashing.
starts flashing.
(Beep)
(Beep...Beep)
(Beep...Bee...p)
Forward
(Beep
Beep)
(Beep
Beep)
Backward
(Beep Beep
Beep)
(Beep Beep
Beep)
SL-SW880 ONLY
To prevent the disc from being scratched or
damaged
damaged
Remove built up dust from the felt pads.
Felt pads