Panasonic th-32lru50 Benutzerhandbuch

Seite von 2
Location
Place the TV at a comfortable distance for viewing. Avoid placing it where sunlight or other bright light (including reflections) 
will fall on the screen. Use of some types of fluorescent lighting can reduce remote control transmitter range. Adequate 
ventilation is essential to prevent an internal component failure. Keep away from areas of excessive heat or moisture.
■ 
Adjust the stand to your desired angle.
The stand angle can be rotate 30°/60°/90° to the right/left. (see Control rotation angle)
a
b
[Rotation angle: 30°]
  TH-32LRU50  a: 9.8 ” (248 mm)
   
b: 7.6 ” (193 mm)
  TH-37LRU50  a: 11.0 ” (279 mm)
   
b: 8.8 ” (222 mm)
  TH-42LRU50  a: 12.5 ” (316 mm)
   
b: 9.8 ” (248 mm)
a
b
[Rotation angle: 60°]
  TH-32LRU50  a: 15.0 ” (381 mm)
   
b: 12.8 ” (323 mm)
  TH-37LRU50  a: 17.1 ” (433 mm)
   
b: 14.7 ” (373 mm)
  TH-42LRU50  a: 19.0 ” (483 mm)
   
b: 16.5 ” (418  mm)
a
b
[Rotation angle: 90°]
  TH-32LRU50  a: 17.3 ” (439 mm)
   
b: 14.2 ” (360 mm)
  TH-37LRU50  a: 19.7 ” (500 mm)
   
b: 16.4 ” (416 mm)
  TH-42LRU50  a: 21.9 ” (555 mm)
   
b: 18.4 ” (467 mm)
■ 
Control rotation angle
The rotation angle can be controlled at 30° or 60°. 
It is not necessary to attach the screws for the 90° angle rotation.
 Temporarily remove the 5 screws shown below.
 Attach 
A
 screws (2) to each angle control position.
Swivel plate 
[Bottom view]
 
1
2
5
4
3
[Front of swivel plate]
[Back of swivel plate]
[For 30°]
[For 60°]
Set-up
6.5” (165 mm)
6.1” (155 mm)
5.7” (144 mm)
a
b
0.079” – 0.091”
(2 – 2.3 mm)
Screw the wood screws (2) into the 
positions  a
 
of the table or desk.
Note
Use  C  wood screws for fixing the 
pedestal. (Total 4 screws) 
B  is used as security screw if necessary.
[Back of fixed plate]
Align the swivel hole in the bottom of the 
swivel plate with wood screws that was 
screwed in previously, and place the TV 
set onto the swivel plate.
Slide the TV set forwards until it stops, 
then fix it in place.
b
Screw the wood screws (2) into the 
holes 
b
 
to fix the pedestal.
[View from above]
• 
Place the TV set in a position where it will not protrude from the table when swiveled.
• 
Make sure there is enough space between the TV set and wall, so that when the TV set is swiveled it does not hit the wall. 
Connecting Antenna
VHF/UHF Antenna
 
NTSC (National Television System Committee):
Conventional broadcasting 
• 
ATSC (Advanced Television Systems Committee):
Digital TV Standards include digital high-definition television (HDTV), standard-definition television (SDTV), data 
broadcasting, multichannel surround-sound audio and interactive television.
Cable
• 
You need to subscribe to a cable TV service to enjoy viewing their programming.
• 
You can enjoy high-definition programming by subscribing to a high-definition cable service.
The connection for high-definition can be done with the use of HDMI or Component Video cable.
• 
To view high-definition programming select the correct video input. 
 HDMI terminals
 COMPONENT terminals
 COMPOSITE terminals
 AUDIO OUT terminals
 DATA/MTI terminal
 SERIAL terminal
 PC terminal
Side panel 
Back panel
*  For more details on the external equipment’s 
connections, please refer to the operating 
manuals for the equipment.
Connection panel
Connections
Power Cord
(Connect after all the 
other connections.)
Cable TV
AC 110-127 V
60 Hz
VHF/UHF Antenna
or
Back of the TV
Panasonic System Communications Company of North America
Unit of Panasonic Corporation of 
North America
Three Panasonic Way, 2F-5, 
Secaucus, NJ 07094
Panasonic Hospitality LCD HDTV
Limited Warranty
Models or Parts
Part
Warranty
Labor
Warranty
Professional Flat
Panel Display
LIMITS AND EXCLUSIONS
There are no express warranties except as listed above.
THE WARRANTOR SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES
(INCLUDING, WITHOUT LIMITION, DAMAGE
TO DISCS) RESULTING FROM THE USE OF THIS
PRODUCT, OR ARISING OUT OF ANY BREACH OF
THE WARRANTY. ALL EXPRESS AND IMPLIED
WARRANTIES, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR
PARTICULAR PURPOSE, ARE LIMITED TO THE
APPLICABLE WARRANTY PERIOD SET FORTH
ABOVE.
Some states do not allow the exclusion or limitation
of incidental or consequential damages, or limitations
on how long an implied warranty lasts, so the above
exclusions or limitations may nor apply to you. This
warranty gives you specific legal rights and you may
other rights, which vary from state to state.
If you have a problem with this product that is not
handled to your satisfaction, then write the Consumer
Affairs Department at the Company address indicated
above.
In the USA and Puerto Rico
FOR SERVICE 
CALL TOLL FREE 
1-800-973-4390
2 Years
2 Years
This warranty is extended only to the original purchaser 
and is non transferable. A purchase receipt or other
proof of date of original purchase will be required before 
warranty service is rendered.
This warranty only covers failures due to defects in 
materials or workmanship, which occur during normal 
use. The warranty does not cover damage which occur 
in shipment, or failures which are caused by products 
not supplied by the warrantor, or failures which result 
from improper installation, set-up adjustments, improper 
antenna, inadequate signal pickup, maladjustment of 
consumer controls, improper operation, power line surge, 
improper voltage supply, lighting damage, or service by 
anyone other than an authorized repair facility, or 
damage that is attributable to acts of God.
Panasonic System Communications Company of North 
America (referred to as “the Warrantor”) will repair this 
product and all included accessories with new or 
refurbished parts, free of charge in the USA or Puerto 
Rico, of the original purchase in the event of a defect in 
materials or workmanship as follows:
On-site or carry-in service in the USA and Puerto Rico 
may be obtained during the warranty period by contacting 
Panasonic System Communications Company of North 
America Service toll free at 1-800-973-4390.
USA only: This product has a fluorescent lamp that contains mercury.
Disposal may be regulated in your community due to environmental considerations. For disposal or recycling information, please visit
Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149.
Customer’s Record
The model number and serial number of this product can be found on its back cover. You should note this serial number in the space provided below and retain this book, 
plus your purchase receipt, as a permanent record of your purchase to aid in identification in the event of theft or loss, and for Warranty Service purposes.
Model 
Number 
   Serial 
Number 
  
© Panasonic Corporation 2012
Panasonic System Communications 
Company of North America
Unit of Panasonic Corporation of North America
Executive Office :
Three Panasonic Way, 2F-5, Secaucus, NJ 07094
Panasonic Canada Inc.
5770 Ambler Drive
Mississauga,Ontario
L4W 2T3 CANADA
Printed in U.S.A.
M0212-1052
Specifications
TH-32LRU50
TH-37LRU50
TH-42LRU50
Power Source
AC 110-127 V, 60 Hz
Power 
Consumption
Rated Power 
Consumption
115  W
165 W
205 W
Standby condition
0.9 W
0.9 W
0.9 W
Display panel
Aspect Ratio
16:9
Visible screen size
(W × H × Diagonal)
(No. of pixels)
32” class 
(31.5 inches measured diagonally)
37” class 
(37.0 inches measured diagonally)
42” class 
(42.0 inches measured diagonally)
27.5 ” × 15.4 ” × 31.5 ”
(698 mm × 392 mm × 800 mm)
32.2 ” × 18.1 ” × 37.0 ”
(819 mm × 460 mm × 940 mm)
36.6 ” × 20.6 ” × 42.0 ” 
 (930 mm × 523 mm × 1, 067 mm)
1,049,088 (1,366 (W) × 
768 (H)) [4,098 × 768 dots]
2,073,600 (1,920 (W) × 1,080(H)) [5,760 × 1,080 dots]
Sound
Speaker
1-way 2 bottom SP System
Audio Output
20 W [10 W + 10 W] (10 % THD)
PC signals
VGA, SVGA, XGA, WXGA, SXGA 
Horizontal scanning frequency 31 - 69 kHz
Vertical scanning frequency 59 - 86 Hz
Channel Capability-
ATSC/NTSC (Digital/Analog)
VHF/ UHF:  2 - 69, CATV:  1 - 135 (support MPEG4 H.264 decode)
Operating Conditions
Temperature: 
32 °F – 95 °F (0 °C – 35°C)
Humidity: 
20 % – 80 % RH (non-condensing)
Connection T
erminals
VIDEO IN 1-2
VIDEO: 
 
RCA PIN Type × 1 1.0 V[p-p] (75 
Ω)
AUDIO L - R: 
RCA PIN Type × 2 0.5 V [rms]
COMPONENT IN
Y: 
 
1.0 V [p-p] (including synchronization)
P
B
, P
R
 
±0.35 V [p-p]
AUDIO L-R:  RCA PIN Type × 2 0.5 V [rms]
HDMI 1-3
TYPE A Connector × 3
 This TV supports “HDAVI Control 5” function.
PC IN
D-SUB 15PIN: 
R,G,B / 0.7 V [p-p] (75 
Ω)
 
 
HD, VD / 1.0 - 5.0 V [p-p] (high impedance)
AUDIO: 
 
M3 JACK × 1  0.5 V [rms]
SERIAL CTRL
M3 Jack × 1 (RS232C)
DATA/MTI
RJ-11C (6pin)
 Multiple Television Interface (MTI)
AUDIO OUT
M3 JACK × 1  0.5 V [rms] (high impedance)
Card slot
SD CARD slot × 1
DIGITAL AUDIO OUT
PCM / Dolby Digital, Fiber Optic
FEATURES
3D Y/C FILTER, CLOSED CAPTION, 
V-Chip, Vesa compatible, Integrated Pro: Idiom
Dimensions
(W × H × D)
Including TV stand
31.5 ” × 21.8 ” × 10.8 ”
(798 mm × 553 mm × 272 mm)
36.1 ” × 24.5 ” × 12.1 ”
(915 mm × 622 mm × 307 mm)
40.2 ” × 26.9 ” × 12.6 ”  
(1, 021 mm × 682 mm × 318 mm)
TV Set only
31.5 ” × 20.2 ” × 3.3 ”
(798 mm × 511 mm × 83 mm)
36.1 ” × 22.8 ” × 3.5 ”
(915 mm × 577 mm × 87 mm)
40.2 ” × 25.1 ” × 4.2 ” 
(1, 021 mm × 637 mm × 105 mm)
Mass
Including TV stand
27.6 lb. (12.5  ) NET
36.9 lb. (16.7  ) NET
47.7 lb. (21.6  ) NET
TV Set only
21.0 lb. (9.5  ) NET
28.7 lb. (13.0  ) NET
38.6 lb. (17.5  ) NET
Note
  Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.
RF connection*
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
LIMITED W
ARRANTY ST
A
TEMENT
Item
Video Tape
P2/SD Cards
Video Heads
D5 Video heads
Maintenance Items
Colour Camera CCD
Imaging Block
BT-H Series LCD Monitors
* DLP™
Projectors
* LCD Projectors above
2,500 ANSI Lumens
* LCD Projectors below
2,500 ANSI Lumens
Projector Lamps
103 inch Plasma displays
Hard Drive Disk Unit
Parts
30 days

Replacement only 
(content not covered)
(Content not covered)
1 year or 2,000 hrs. (prorated) 
Whichever comes first
1 year or 
1,0
00 hrs. 
Whichever comes first
90 days
2 years
2 years
3 years or 17,000 hrs. 
Whichever comes first
3 years or 2,500 hrs. 
Whichever comes first
3 years or 1,500 hrs. 
Whichever comes first
50% of the rated lamp life or 1 year. 
Whichever comes first
3 years (burn-in not covered)
1 year plus balance (if any) of
the original Manufacturer’s
Limited Warranty. 
(Content not covered)
Labour
N/A
N/A
1 year or 2,000 hrs. 
Whichever comes first
1 year or 1,000 hrs. 
Whichever comes first
90 days
2 years
2 years
3 years or 17,000 hrs. 
Whichever comes first
3 years or 2,500 hrs. 
Whichever comes first.
3 years or 1,500 hrs. 
Whichever comes first
50% of the rated lamp life or 1 year. 
Whichever comes first.
3 years 
1 year
WARRANTY COVERAGE PERIOD EXCEPTIONS
Panasonic Canada Inc. (also known as PCI) warrants this product to be free of 
defects in material and workmanship under normal use during the applicable 
warranty coverage period described below. PCI agrees to repair, or at its option, 
exchange, any part that becomes defective. However, the product must be 
purchased and serviced in Canada. The product or part that shows evidence of 
defect must be delivered prepaid or carried in to an authorized Panasonic Broadcast 
Service Center. This warranty does not cover shipping costs. 
The warranty coverage period is one year for both parts and labour beginning with 
the date of original end user purchase, subject to the exceptions as stated below. 
Repaired or replacement parts supplied during the warranty coverage period carry 
the unexpired portion of the original warranty coverage period. Proof of product 
purchase is a condition of warranty service. The owner must produce the product 
purchase receipt or other satisfactory evidence of date of original purchase. 
This warranty does not apply to external appearance items, such as handles, knobs, 
safety windows, etc. This warranty does not apply to any part, or parts, of the 
product, installed, altered, repaired or misused in any way that, in the opinion of PCI, 
affects the reliability of or detracts from the performance of the product. 
For products requiring routine preventive maintenance, that maintenance must be 
performed in order to maintain warranty coverage. 
Serial numbers that have been altered, defaced or removed void this warranty. This 
warranty does not cover replacements or repairs necessitated by loss or damage 
resulting from any cause beyond the control of PCI. 
Marking or retained images (sometimes called “burn-in”) resulting from the display of 
fixed images on video display products are not defects and are not covered under 
this warranty.
In certain instances, some jurisdictions do not allow the exclusion or limitation of 
incidental or consequential damages, or the exclusion of implied warranties, so the 
above limitations and exclusions may not be applicable.
Warranty Service
If the product needs to be shipped for service, carefully pack (preferably in the 
original carton) and enclose a letter, detailing the complaint. Send prepaid and 
adequately insured to the local authorized Panasonic Service Centre in your 
area or to Panasonic Technical Support and Product Services Department, 5770 
Ambler Drive, Mississauga, Ontario, L4W 2T3. Shipping to the latter location 
requires a return authorization before shipment. No liability is assumed for loss 
or damage to the product while in transit.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER 
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 
PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR 
ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.
• 
Dust, smoke, rental/staging environment and twenty-four/seven operation, 
dramatically decreases the interval between performances of routine preventive 
maintenance required to maintain this warranty coverage.
2 years (burn-in not covered)
2 years
All Plasma displays
(for Canada)
(for the U.S.A and Puerto Rico)
Accessories
A
 
Screws (2)
 XSN3+4FJ
  size (M3 × 4)
B
 
Security screw (2)
 THM2AB001
C
 
Wood screws (4)
 XTS5+20AFJK