Yamaha mfc10 Benutzerhandbuch
11
Normal Mode
How to Edit Memory
If the FUNCTION lamp is lit, press [FUNCTION], so that the
lamp is off, and Program Change Memory is enabled.
1
Select the Memory Number to be edited (see page 9). Press
[MEMORY EDIT] to edit to begin editing that Memory
Number. (The lamp above that foot switch and the STATUS
lamp will flash.)
[MEMORY EDIT] to edit to begin editing that Memory
Number. (The lamp above that foot switch and the STATUS
lamp will flash.)
2
Press [MEMORY EDIT] to cycle through the 4 edit param-
eters (the selected parameter’s light will flash).
eters (the selected parameter’s light will flash).
3
Use [INC/YES] and [DEC/NO] to edit the parameter.
Press [INC/YES] to increase the value shown in the LED
display by 1, press [DEC/NO] to decrease the value by 1. By
holding a button, values will continuously increase or de-
crease.
display by 1, press [DEC/NO] to decrease the value by 1. By
holding a button, values will continuously increase or de-
crease.
Hold the [INC/YES] button and press the [DEC/NO] button
and the value shown in the LED display will increase by 10.
Repeatedly press [DEC/NO] to continue increasing the value
by 10.
and the value shown in the LED display will increase by 10.
Repeatedly press [DEC/NO] to continue increasing the value
by 10.
Hold the [DEC/NO] button and press the [INC/YES] button
and the value shown in the LED display will decrease by 10.
Repeatedly press [INC/YES] to continue decreasing the value
by 10.
and the value shown in the LED display will decrease by 10.
Repeatedly press [INC/YES] to continue decreasing the value
by 10.
• TOGGLE ON-OFF/NUMBER OF PGM can not be
selected from Program Change Memory.
MEMORY
EDIT
Increase by 10
MEMORY
EDIT
DEC
/NO
/NO
INC
/YES
±10
DEC
/NO
/NO
INC
/YES
±10
001
128
128
001
DEC
/NO
/NO
INC
/YES
±10
DEC
/NO
/NO
INC
/YES
±10
Decrease by 10
WRITE
/EXIT
007
STATUS
DATA/CTRL
DATA/CTRL
BANK MSB/MAX
BANK LSB/MIN
BANK LSB/MIN
TOGGLE ON-OFF
/NUMBER OF PGM
/NUMBER OF PGM
STATUS settings
DATA/CONTROL settings
BANK MSB settings
BANK LSB settings
5
Press [INC/YES], to save the edited data to the current
Memory Number, The MFC10 will return to its normal control
mode.
Memory Number, The MFC10 will return to its normal control
mode.
Press [DEC/NO] to cancel the save operation of the edited
data. At this time the memory will revert to its pre-edited
contents.
data. At this time the memory will revert to its pre-edited
contents.
DEC
/NO
/NO
INC
/YES
±10
DEC
/NO
/NO
INC
/YES
±10
• Another Memory Number from the same bank (10’s digit bank) can be easily edited by
pressing [1] - [0] without exiting from the edit mode. You must execute or cancel the save
operation for the currently edited data (the current Memory Number will flash) before
proceeding to edit the new number. Use [INC/YES] to execute or [DEC/NO] to cancel the
save operation. If data has not been edited, the Memory Number will not flash and the
newly selected Memory Number will be shown in the display.
operation for the currently edited data (the current Memory Number will flash) before
proceeding to edit the new number. Use [INC/YES] to execute or [DEC/NO] to cancel the
save operation. If data has not been edited, the Memory Number will not flash and the
newly selected Memory Number will be shown in the display.
4
After the desired parameters have been edited in steps
2
and
3
,
press [WRITE/EXIT]. The Memory Number shown in the
LED display will flash. (The flashing number indicates
confirmation is necessary to proceed or cancel saving of the
edited data.)
LED display will flash. (The flashing number indicates
confirmation is necessary to proceed or cancel saving of the
edited data.)
• If data has not been edited, the Memory Number will
not flash and the MFC10 will return to its normal
control mode.