Technicolor - Thomson 25922 Benutzerhandbuch

(for model 25922xx1)

Make sure your package includes the items shown here.

NOTICE: This product meets the applicable Industry Canada technical specifications.
Operation is subject to the following two conditions: (1) This device may not cause 

interference, and (2) This device must accept any interference, including interference 

that may cause undesired operation of the device.
The equipment must be installed using an acceptable method of connection. The 

customer should be aware that compliance with the above conditions may not prevent 

degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian 

maintenance facility designated by the supplier. Any repairs or alterations made by the 

user to this equipment, or equipment malfunctions, may give the telecommunications 

company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of 

the power utility, telephone lines and internal metallic water pipe systems, if present, 

are connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should 

contact the appropriate electric inspection authority, or electrician, as appropriate.
NOTES: This equipment may not be used on coin service provided by the telephone 

company.

1. Locate battery and battery door which are packaged together inside a plastic bag 

and are separate from the handset.

2.  Locate the battery compartment on the back of the handset.
3.  Plug the battery pack cord into the jack inside the compartment. 

PLEASE REGISTER 

shows in the display.

2.  Plug one end of the telephone line cord into the TEL LINE jack at the back of the base 

and the other end into a modular jack.

3.  Plug the AC power converter into the electrical outlet and the DC connector into the 

jack at the back of the base.

4.  Place the handset in the base cradle. The charge/in use indicator turns on, verifying 

the battery is charging. The unit will take 20 seconds to register and verify its security 

code. 

READY shows in the handset’s display.

UNAVAILABLE when the TALK/CALL BACK button is pressed. You 

5.  Allow the phone to charge for 16 hours prior to first use. If you don’t properly charge 

the phone, battery performance is compromised. 

1.  Turn the base over.
2.  Attach the wall mounting pedestal by first inserting the tabs on the open edge of 

the pedestal into the slots on the lower portion of the bottom of the base. Then push 

down and snap the pedestal into place.

3.  Slip the mounting holes (on the back of the base) over the wall plate posts, and slide 

the unit down into place. (Wall plate not included.)

There are eight programmable menus available: Language, Handset Name, Area Code, 

Ringer On/Off, Ringer Tone, Tone/Pulse, Transfer ON/OFF and Default Setting.
During programming, you may press the 

mute/menu button at any time to go to the 

next option. To exit the menu, keep the previous setting and return to the standby 

mode, press the 

*tone/exit button.

1.  Press the 

mute/menu button until 41ENG 2FRA 3ESP shows in the display. 1ENG is 

the default. (ENG stands for English. FRA stands for French. ESP stands for Spanish.)

2.  Use the 

CALLER ID-VOLUME (5or6) button or the touch-tone pad on the handset 

to enter your selection.

3.  Press 

mute/menu again to save.

1.  Press the 

mute/menu button until ENTER NAME shows in the display. 

2. Use the touch-tone pad on the handset to enter the name (up to 15 characters). 

More than one letter is stored in each of the number keys. For example, to enter the 

name Bill Smith, press the 2 key twice for the letter B. Press the 4 key 3 times for the 

letter I. Press the 5 key 3 times for the letter L. Wait for one second. Press the 5 key 3 

times for the second letter L. Press the 1 key to insert a space between the L and the 

S. Press the 7 key 4 times for the letter S; press the 6 key once for the letter M; press 

the 4 key 3 times for the letter I; press the 8 key for the letter T; press the 4 key twice 

for the letter H..

3.  Press 

mute/menu again to save.

: If no name is entered, READY shows in the display.

1.  Press the 

mute/menu button until AREA CODE - - - shows in the display. - - - is 

the default. 

2.  Use the touch-tone pad on the handset to enter your three digit area code.
3.  Press 

mute/menu again to save.

1.  Press the 

mute/menu button until RINGER 41 ON shows in the display.  

1 ON is the default.

2. Use the 

CALLER ID-VOLUME (5or6) button or the touch-tone pad on the handset 

to scroll to 

1 ON or 2 OFF.

3.  Press 

mute/menu to save.

NOTE: If you turn the ringer off, RINGER OFF shows on the display.

You can choose from 3 ring tones.
1.  Press the 

mute/menu button until RINGER TONE 401 shows in the display.  

01 is the default.

2. Use the 

CALLER ID-VOLUME (5or6) button on the handset to select from 

01 to 03.

3.  Press 

mute/menu to save.

1.  Press the 

mute/menu button until 41 TONE 2 PULSE shows in the display.  

1 TONE is the default.

2. Use the 

CALLER ID-VOLUME (5or6) button or the touch-tone pad on the handset 

to scroll to 

1 TONE or 2 PULSE.

3.  Press 

mute/menu to save.

In order to use the Call Transfer feature (applicable ONLY with additional handsets), 

you must have the Transfer ON/OFF set to ON through the menu of the transferring 

handset. 
1.  Press the 

mute/menu button until TRANSFER 41 OFF shows in the display. 

2.  Use the 

CALLER ID-VOLUME (5or6) button or the touch tone pad on the handset 

and select 

1OFF.

3.  Press 

mute/menu again to save.

You may return handset settings to the factory default setup using this menu.
1.  Press the 

mute/menu button until DEFAULT 4NO shows in the display. NO is  

the default.

2.  Use the 

CALLER ID-VOLUME (5or6) button on the handset to scroll to 

YES or NO.

3.  Press 

mute/menu to save. 

The phone is 

ON when the charge/in use indicator on the base is lit. The handset visual 

ringer and base indicator flash when you receive a call.

1.  When the phone rings, pick up the handset and press the 

TALK/CALL BACK button.

2.  When finished, press the 

TALK/CALL BACK button again or place the handset on the 

base cradle to hang up.

1.  Pick up the handset and press the 

TALK/CALL BACK button. Wait for the dial tone. 

The call timer starts counting minutes and seconds in the display.

2.  Dial a telephone number.
3.  When finished, press the 

TALK/CALL BACK button again or place the handset on the 

base cradle to hang up.

UNAVAILABLE when the TALK/CALL BACK button is pressed. You 

1.  Make sure the phone is 

OFF (not in TALK mode).

2.  Dial a telephone number (the number you dial shows in the display).

3.  Press the 

TALK/CALL BACK button on that handset. The number auto-matically dials 

and the call timer starts counting the minutes and seconds in the display.

4.  When finished, press the 

TALK/CALL BACK button again to hang up.

While the phone is 

ON (in TALK mode), press the redial button to redial the last number 

you dialed (up to 32 digits).

   

While the phone is 

OFF (in standby mode), press the redial button and then the  

TALK/CALL BACK button to redial the last number.

Use the 

flash/call waiting button to activate custom calling services such as call 

waiting, which are available through your local phone company.

While talking on the phone, it may be necessary for you to manually change the 

channel to improve reception and reduce noise or static on the line. Press and release 

the 

chan button to move to the next clear channel.

Press the 

*tone/exit button to cancel any command you initiated.

This feature assists in locating a misplaced handset.
Press the 

page button on the base. The handset beeps continuously for about 2 

minutes until you press the 

TALK/CALL BACK button on the handset or the page button 

on the base.

Apart from the setting in the main menu, there is a shortcut to set the ringer. Make sure 

the phone is 

OFF (not in talk mode).

1. Press the 

#PAUSE/ringer button to go to the RINGER ON/OFF menu.  

RINGER 41 ON shows in the display. 1 ON is the default.

2. Use the 

CALLER ID-VOLUME (5or6) button or the touch-tone pad on the handset 

to scroll to 

1 ON or 2 OFF.

3. Press the 

#PAUSE/ringer button to save your selection. You will hear a 

confirmation tone.

When the phone is 

ON (in TALK mode) press the CALLER ID-VOLUME (5or6) button to 

adjust the listening level. Choose from five volume settings. 

VOL 1 is the lowest volume 

and 

VOL 5 is the highest volume.

NOTE: The phone will automatically reset VOL 5 to VOL 4 after you 

Use mute during a phone conversation to speak privately and off-line with a third party.
1.  Press the 

mute/menu button. MUTE shows in the display. The party on the telephone 

will not hear you.

2.  Press the 

mute/menu button when finished.

Model 25922C 

00017557 (Rev. 4 CAN E) 

08-05 

Printed in China

For 

Model 25922xx2 there will be ONE additional handset, charge cradle, battery pack 

and cover than shown above.
For 

Model 25922xx3 there will be TWO additional handsets, charge cradles, battery 

packs and covers than shown above.
For 

Model 25922xx4 there will be THREE additional handsets, charge cradles, battery 

packs and covers than shown above.

To use this phone, you need an RJ11C type modular telephone 

jack, which might look like the one pictured here, installed in 

your home. If you don’t have a modular jack, call your local 

phone company to find out how to get one installed.

Your cordless phone uses a digital security system to protect against false ringing, 

unauthorized access, and charges to your phone line.

•  Avoid sources of noise and heat, such as motors, fluorescent lighting, microwave 

ovens, heating appliances and direct sunlight.

•   Avoid areas of excessive dust, moisture and low temperature.
•   Avoid other cordless telephones or personal computers.
•  Never install telephone wiring during a lightning storm.
•  Never install telephone jacks in wet locations unless the jack is specifically 

designed for wet locations.

•  Never touch non-insulated telephone wires or terminals, unless the telephone line 

has been disconnected at the network interface.

•  Use caution when installing or modifying telephone lines.

This feature is useful only if you have pulse (rotary) service. Temporary Tone Dialing 

enables pulse (rotary) service phone users to access touch tone services offered by 

banks, credit card companies, etc. For example, when you call your bank you may need 

to enter your bank account number. Temporarily switching to touch tone mode allows 

you to send your number.
1.  Dial the telephone number and wait for the line to connect.
2.  When your call is answered, press the 

*tone/exit button on the handset to 

temporarily change from pulse dialing to tone dialing.

3.  Follow the automated instructions to get the information you need.
4.  Hang up the handset and the phone automatically returns to pulse (rotary)  

dialing mode.

During an external call, you may transfer the external call to another handset.
1.  Press the 

format/trans button on the originating handset. TRANSFERRING shows in 

the display. All registered handsets will be paged.

2.  Press the 

format/trans button or TALK/CALL BACK on receiving handset to answer 

call.

This unit receives and displays information transmitted by your local phone company. 

This information can include the phone number, date, and time; or the name, phone 

number, date, and time. 

Provided you subscribe to Call Waiting Caller ID service from your phone company; if 

you receive an incoming call and you are already on the phone, a beep indicates the 

presence of a Call Waiting call on the line. Only the handset that is in use at the time of 

the call will display and store the Call Waiting Caller ID information.

•  When you hear the call waiting beep in the handset receiver, press the 

call waiting button to put the current call on hold and answer the incoming call. 

Press the 

flash/call waiting button again to return to the original call. 

When you receive a call, the Caller ID information is transmitted between the first and 

second ring. The Caller ID information appears on the display while the phone rings, 

giving you a chance to monitor the information and decide whether or not to answer 

the call.

If you are not at home or cannot answer, your telephone’s Caller ID memory stores the 

data for the 40 most recent calls you received so you can see who called while you 

were unavailable. When the 41st call is received, the oldest Caller ID record (1st call) is 

automatically deleted.
You may review the stored information at any time. Calls received since your last review 

show as 

NEW in the display. Calls that have not been previously reviewed but were 

received from the same number more than once show as 

REPT in the display.

This equipment generates and uses radio frequency energy which may interfere 

with residential radio and television reception if not properly installed and used in 

accordance with instructions contained in this manual. Reasonable protection against 

such interference is ensured, although there is no guarantee this will not occur in a 

given installation. If interference is suspected and verified by switching this equipment 

on and off, the user is encouraged to try to correct the interference by one or more of 

the following measures: Reorient the radio/television receiver’s antenna, relocate the 

equipment with respect to the receiver, plug the equipment and receiver into separate 

circuit outlets. The user may also wish to consult a qualified radio/television technician 

for additional suggestions. This equipment has been fully tested and complies with all 

limits for Class B computing devices pursuant to part 15 FCC Rules and Regulations. 

Should your equipment cause trouble on your line which may harm the telephone 

network, the telephone company, where practicable, may notify you that temporary 

discontinuance of service may be required. Where prior notice is not practicable and 

the circumstances warrant such action, the telephone company may temporarily 

discontinue service immediately.
The telephone company may make changes in its communications facilities, 

equipment, operations or procedures where such action is required in the operation 

of its business. If these changes are expected to affect the use or performance of your 

telephone equipment, the telephone company will likely give you adequate notice to 

allow you to maintain uninterrupted service.
Notice must be given to the telephone company upon termination of your telephone 

from your line.

On the bottom of this equipment is a label indicating, among other information, the 

Ringer Equivalence Number (REN) for the equipment. 
The REN is useful in determining the number of devices you may connect to your 

telephone line and still have all of these devices ring when your telephone number is 

called. In most (but not all) areas, the sum of the RENs of all devices connected to one 

line should not exceed 5. To be certain of the number of devices you may connect to 

your line as determined by the REN, you should contact your local telephone company.

Licensed under US Patent 6,427,009.

This telephone system meets FCC/Industry Canada standards for Hearing Aid 

Compatibility.

This equipment complies with FCC RF radiation exposure limits set forth for an 

uncontrolled environment. This equipment should be installed and operated with 

a minimum distance of 20 centimeters between the radiator and your body. This 

transmitter must not be co-located or operated in conjunction with any other antenna 

or transmitter.

1.  Choose an area near an electrical outlet and a telephone wall jack (RJ11C), and 

place your cordless telephone on a level surface, such as a desktop or tabletop, or 

you may mount it on the wall.

4.  Insert the battery pack.
5.  Close the battery compartment by pushing the door up until it snaps into place.

30 Eglinton Ave W., Suite 304

Mississauga, ON Canada L5R 3E7 

© 2008 Thomson Digital Technologies Ltd. 

Trademark(s) ® Registered

Marque(s) ® déposée(s)

CALLER ID-VOLUME (6) 

CALLER ID-VOLUME (5)