Edelbrock torker ii 5081 Benutzerhandbuch

PLEASE study these instructions carefully before beginning this installation.  Most installations can be accomplished with common tools and
procedures.  However, you should be familiar with and comfortable working on your vehicle.  If you do not feel comfortable performing this
installation, it is recommended to have the installation completed by a mechanic.  If you have any questions, please call our 

Technical Hotline

at: 1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday or e-mail us at edelbrock@edelbrock.com.

•

MANIFOLD:  The Torker II manifold is designed for 351 c.i.d. Ford Windsor small-block V8 engines, and is recommended for street high
performance and race vehicles only.  The Torker II manifold is of single-plane design utilizing modern air flow technology.  It provides good
low rpm response plus increasing performance above the 5000 rpm range.  It also provides horsepower and torque increases within the listed
rpm range when used with any mix of aftermarket equipment available for vehicles operating within that range.

•

EGR SYSTEM: This manifold will not accept stock EGR (exhaust gas recirculation equipment).  EGR systems are used on most 1972 and
later model vehicles.  Check local laws for requirements.

•

ACCESSORIES & INSTALLATION ITEMS: Major recommendations are listed below.  See our catalog for details.  To order a catalog, call
(800) FUN-TEAM, or visit www.edelbrock.com.

•

CARBURETOR RECOMMENDATIONS:

TORKER II INTAKE MANIFOLD

For Ford 351 C.I.D. Windsor V8 Engines

Catalog #5081

INSTALLATION INSTRUCTIONS

CARBURETOR

REFERENCE

PARTS REQUIRED FOR INSTALLATION

Performer #1407 (750 cfm)

A, I, K, N, O

#1490 or 1845 throttle plate kit, #1483 or 1844 throttle lever adapter

Performer #1411 (750 cfm)

A, I, K, N

#1490 or 1845 throttle plate kit, #1483 or 1844 throttle lever adapter

Performer #1412 (800 cfm)

A, I, K, N, O

#1490 or 1845 throttle plate kit, #1483 or 1844 throttle lever adapter

Performer #1413 (800 cfm)

A, I, K, N

#1490 or 1845 throttle plate kit, #1483 or 1844 throttle lever adapter

Thunder Series #1812 (800 cfm) A, I, K, N

#1490 or 1845 throttle plate kit, #1483 or 1844 throttle lever adapter

Thunder Series #1813 (800 cfm) A, I, K, N

#1490 or 1845 throttle plate kit, #1483 or 1844 throttle lever adapter

A - Carburetor will work with non-EGR or pre-emission control systems.

I - Carburetor has no provisions for evaporative canister.

K - Carburetor requires #8008 or #8024 stud, washer and nut kit.  Determine proper length based on gasket thickness and your accessory

mounting requirements.

N - Carburetor accepts factory cruise control

O - Carburetor comes with manual choke.  It can be converted to electric choke using kit #1478.

INTAKE MANIFOLD

REFERENCE

RECOMMENDED GASKET

5081

(None)

Edelbrock #7220  Port:  1.20” x 2.00”, .060” Thickness

NOTE:  To ensure maximum performance and a proper seal, Edelbrock gaskets which are

specifically designed and manufactured for use with Edelbrock parts must be used.

•

BRACKETS:  A throttle mounting adapter plate is supplied with each manifold to adapt both early and later type throttle brackets to our
manifolds, as shown in Figure 1.

•

GASKETS: Do not use competition style intake gaskets for this street manifold.  Due to material deterioration over time, internal leakage of
vacuum, oil, and coolant may occur.

•

SPECIAL INSTRUCTIONS:  On some applications there may be an interference problem with the stock air cleaner.  If this problem occurs,
use the Edelbrock adapter, catalog #8092.  

CAUTION: Check hood for clearance before closing hood when using these spacers.