Sears 139.18847 Benutzerhandbuch
4
Safety Reversing Sensor
Horizontal and vertical reinforcement
is needed for lightweight garage doors
(fiberglass, steel, aluminum, door with glass panels, etc.).
See page 24 for details.
Support bracket &
fastening hardware
is required.
See page 17.
Trolley
Cable
Emergency
Release
Rope &
Handle
Garage
Door
Straight
Door
Arm
Curved
Door Arm
Slack in Chain Tension
is Normal When
Garage Door is Closed
Open Position
T-rail
— — — — — — — —
Door Center
Header Wall
Safety
Reversing
Sensor
Floor must be level
across width of door
FINISHED CEILING
Extension Spring
Torsion Spring
Access Door
OR
Cable Pulley
Bracket
Header
Bracket
Trolley
Straight
Door
Arm
Emergency
Release
Rope & Handle
Door Bracket
Garage
Door
Curved
Door
Arm
Garage
Door
Spring
Header
Wall
Cable
Closed Position
Rail Assembly
Before you begin, survey your garage area to see whether any of the conditions below apply to your installation.
Based on your particular requirements, there are
several installation steps which might call for
materials and/or hardware not included in the carton.
several installation steps which might call for
materials and/or hardware not included in the carton.
• Step 1, page 12 - Look at the wall or ceiling above
the garage door. The header bracket
must be
securely fastened to structural supports.
• Step 5, page 17 - Do you have a finished ceiling in
your garage? If so, a support bracket and
additional fastening hardware may be required.
additional fastening hardware may be required.
• Safety reversing sensor, page 21 - Depending
upon garage construction, wood blocks may need
to be fastened to mounting locations before
sensors are installed.
to be fastened to mounting locations before
sensors are installed.
• Step 10, page 22 - Alternate floor mounting of the
safety reversing sensor will require hardware not
provided.
provided.
• Step 11, page 24 - Do you have a steel, aluminum,
fiberglass or glass panel door? If so, horizontal
and vertical reinforcement is required.
and vertical reinforcement is required.
• Look at the garage door where it meets the
floor. It must close on the floor all the way
across. Otherwise, the safety reverse system
may not work properly. See page 30. Floor or
door should be repaired.
across. Otherwise, the safety reverse system
may not work properly. See page 30. Floor or
door should be repaired.
Safety Reversing Sensor
Horizontal and vertical reinforcement
is needed for lightweight garage doors
(fiberglass, steel, aluminum, door with glass panels, etc.).
See page 24 for details.
Support bracket &
fastening hardware
is required.
See page 17.
Trolley
Cable
Emergency
Release
Rope &
Handle
Garage
Door
Straight
Door
Arm
Curved
Door Arm
Slack in Chain Tension
is Normal When
Garage Door is Closed
Open Position
T-rail
— — — — — — — —
Door Center
Header Wall
Safety
Reversing
Sensor
Floor must be level
across width of door
FINISHED CEILING
Extension Spring
Torsion Spring
Access Door
OR
Cable Pulley
Bracket
Header
Bracket
Trolley
Straight
Door
Arm
Emergency
Release
Rope & Handle
Door Bracket
Garage
Door
Curved
Door
Arm
Garage
Door
Spring
Header
Wall
Cable
Closed Position
Rail Assembly
Closed Position
SECTIONAL Door Installation
• If your door is more than 7 feet high, see the rail
extension kits available on page 38.
• The opener can be installed within 2 feet to the left
or right of the door center if there is a torsion spring
or center bearing plate in the way of the header
bracket or door bracket area.
or center bearing plate in the way of the header
bracket or door bracket area.
If your door has
extension springs, the opener must be installed
in the center of the door. See pages 12 and 24.
in the center of the door. See pages 12 and 24.
• Do you have an access door in addition to the
garage door? If not, Model 18752 Outside
Trolley Release is required. See page 38.
Trolley Release is required. See page 38.
You may find it
helpful to refer
back to this page
as you proceed
with the installation
of your opener.
helpful to refer
back to this page
as you proceed
with the installation
of your opener.