Epson stylus c64 Benutzerhandbuch
EPSON Stylus C63/64/83/84
Revision A
Disassembly and Assembly
Disassembly
14
1.3.2 ASF unit removal
o
External view
Figure 1-3. ASF unit removal
o
Part/Unit that should be removed before removing ASF unit
Housing (Right/Left/Frame)
o
Removal procedure
1) Remove three screws for securing ASF unit to main frame, and remove the unit
with pulling up slightly to the backside of the printer.
2) Release left protrusion of Hopper by pulling its bottom toward the front side,
and remove Hopper from ASF frame.
with pulling up slightly to the backside of the printer.
2) Release left protrusion of Hopper by pulling its bottom toward the front side,
and remove Hopper from ASF frame.
3) Release Extension spring 0.585 for Paper return lever, and remove the lever
with releasing two protrusions.
4) Release Compression spring 1.88 for Returd roller unit, and turn the roller unit
until it is free.
with releasing two protrusions.
4) Release Compression spring 1.88 for Returd roller unit, and turn the roller unit
until it is free.
Screw type : C.B.S SCREW, 3x6, F/SN
Order of tightening : First
Thghtening torque : 8±1 kgf.cm
Screw type : C.B.S-TITE (P4), 3x6, F/SN
Order of tightening : Second
Thghtening torque : 8±1 kgf.cm
Screw type : C.B.P-TITE, 3x8, F/SN
Order of tightening : Third
Thghtening torque : 6±1 kgf.cm
ASF unit (Backside)
Extension spring 0.585
Compression spring 1.88
1
2
1
2
1
This marking is
dowel/latched
position and the
order of assembling.
1
2
Paper return lever
Ribs of ASF frame
o
When assembling ASF unit,
n
Make sure to latch Extension spring 0.585 for Paper
return lever & Compression spring 1.88 for Returd
roller unit in the order indicated in the figure, and to set
Expression spring 0.585 between ribs of ASF frame.
return lever & Compression spring 1.88 for Returd
roller unit in the order indicated in the figure, and to set
Expression spring 0.585 between ribs of ASF frame.
n
Make sure that Paper return lever & Returd roller unit
move smoothly.
move smoothly.
n
Do not touch returd roller and cork on Hopper.
n
Hook two dowels for securing Paper return lever to ASF
frame in the order incicated in the figure.
frame in the order incicated in the figure.
o
When assembling ASF unit to main frame,
n
Make sure to install Compression spring 2.53 for
Hopper correctly.
Hopper correctly.
n
Make sure that Hopper moves smoothly.
n
Make sure to set ASF unit with the flat surface of LD
roller up.
roller up.
n
Fasten three screws for securing ASF unit in the order/
tightening torque indicated in the figure.
tightening torque indicated in the figure.
n
Make sure that there is no gap between ASF unit and
Shield plate (upper) of PS board unit.
Shield plate (upper) of PS board unit.
A D J U S T M E N T
R E Q U I R E D
o
When you replace ASF unit with new one, lubricate it with
the suitable amount of G-26 grease by the specified position.
the suitable amount of G-26 grease by the specified position.
o
When ASF unit is removed or replaced with new one, the
following adjustment must be performed in the order below.
1) Top margin adjustment
2) 1st dot adjustment
following adjustment must be performed in the order below.
1) Top margin adjustment
2) 1st dot adjustment