Hitachi 31cx4b, 31ux5b Benutzerhandbuch
USING THE GENIUS REMOTE TO LEARN ADDITIONAL
FUNCTIONS FOR CLU-851GR
FUNCTIONS FOR CLU-851GR
45
If the storing was not done correctly, or the codes are too long to learn, or no more codes can be
stored in memory due to memory overflow, the LEARN indicator and READY indicator will
flash ON and OFF.
stored in memory due to memory overflow, the LEARN indicator and READY indicator will
flash ON and OFF.
V
V
V
V Set the LEARN/USE mode select switch on the back of the Genius Remote to "USE" and
check that the button to which the code is stored operates correctly. If it does not operate
correctly, repeat from step 1.
check that the button to which the code is stored operates correctly. If it does not operate
correctly, repeat from step 1.
W
W
W
W Repeat steps 3 to 5 to store other keys.
To clear the stored codes from the USER mode
Set the MULTI-PAGE select switch to the USER mode and LEARN/USE mode select switch to
"LEARN". Then, press the POWER and the MUTE buttons simultaneously for 3 seconds. The
"READY" and "LEARN" LEDs will light together. All MULTI-PAGE KEYS with codes are
reset to their initial states.
To remember stored codes, it is convenient to paste the labels (user's label) provided on the
buttons for the USER page. If the correct labels are not provided, it is possible to write these
letters on an empty label with a ballpoint pen.
Set the MULTI-PAGE select switch to the USER mode and LEARN/USE mode select switch to
"LEARN". Then, press the POWER and the MUTE buttons simultaneously for 3 seconds. The
"READY" and "LEARN" LEDs will light together. All MULTI-PAGE KEYS with codes are
reset to their initial states.
To remember stored codes, it is convenient to paste the labels (user's label) provided on the
buttons for the USER page. If the correct labels are not provided, it is possible to write these
letters on an empty label with a ballpoint pen.
Example of User's Labels
NOTE:
1. To operate your TV, be sure to point the Genius Remote at the remote sensor on the television. To
operate other electronic equipment like a VCR, point the remote at the sensor on the device.
2. Refer to the instruction manual of the VCR for operation on the buttons exclusively for the VCR.
3. Be sure to keep the original remote transmitter even after storing its codes in the Genius Remote
Control.
4. If the Genius Remote is left with its batteries removed, the learned codes in its memory are erased
and will have to be reprogrammed into the memory.
5. The Genius Remote Control may not be able to learn certain special remote codes.
1. To operate your TV, be sure to point the Genius Remote at the remote sensor on the television. To
operate other electronic equipment like a VCR, point the remote at the sensor on the device.
2. Refer to the instruction manual of the VCR for operation on the buttons exclusively for the VCR.
3. Be sure to keep the original remote transmitter even after storing its codes in the Genius Remote
Control.
4. If the Genius Remote is left with its batteries removed, the learned codes in its memory are erased
and will have to be reprogrammed into the memory.
5. The Genius Remote Control may not be able to learn certain special remote codes.
CAUTION ON BATTERIES:
1. The Genius Remote Control is working when the LEARN indicator lights up when a button is
pressed.
2. When you press a button and the learn indicator will not light up or if the operation is extremely
slow, this is an indication that the batteries should be replaced.
3. Even if the batteries seem dead, do not remove them until you have replacement batteries ready to
put in. The codes stored in memory will be erased in a few minutes without power. When replacing
batteries, prepare the new ones first.
1. The Genius Remote Control is working when the LEARN indicator lights up when a button is
pressed.
2. When you press a button and the learn indicator will not light up or if the operation is extremely
slow, this is an indication that the batteries should be replaced.
3. Even if the batteries seem dead, do not remove them until you have replacement batteries ready to
put in. The codes stored in memory will be erased in a few minutes without power. When replacing
batteries, prepare the new ones first.