ICOM ic-m801gmdss Benutzerhandbuch
10
40
MEMORY OPERATION
■ Memory description
The IC-M801GMDSS has several kinds of memories
as follows:
as follows:
• Address and group ID code memories (p. 41)
• Call, traffic and scan frequency memories (p. 42)
• DSC transmission memory (described in this section)
• Received message memory (p. 29)
• Call, traffic and scan frequency memories (p. 42)
• DSC transmission memory (described in this section)
• Received message memory (p. 29)
■ Memory writing
10 DSC transmission memory channels allow you to
set often used format specifiers and contents such as
for routine calls, group calls, etc.
set often used format specifiers and contents such as
for routine calls, group calls, etc.
q During DSC watch mode, select the desired format
category (except distress and test), and set the
message, call and traffic frequencies until the call
stand-by screen is displayed as described in the
CALL PROCEDURE section (pgs. 18–27).
message, call and traffic frequencies until the call
stand-by screen is displayed as described in the
CALL PROCEDURE section (pgs. 18–27).
w Push and hold [ENT] for 1 sec. to select the TX
memory write condition.
e Rotate [CH] to select the desired memory channel.
r Push and hold [ENT] for 1 sec. again to store the
condition into the selected memory channel.
• The set DSC format and calling station ID/name ap-
pear.
t Push [ENT] to return to the calling stand-by condi-
tion, or push [MODE
SET
] to return to DSC watch
mode.
- - - T X m e m o r y w r i t e - - - -
0 : I n d i v i d u a l 9 8 7 6 5 4 3 2 1
1 :
2 :
3 :
4 :
5 :
Ç
O K
S E L
- - - T X m e m o r y w r i t e - - - -
0 :
1 :
2 :
3 :
4 :
5 :
Ç
W r i t e
S E L
■ Memory reading/transmitting/deleting
q Push [DSC] to select DSC watch mode, if neces-
sary.
w Push [TX
TXF
] to enter the DSC transmit memory
screen.
• Or, push [MODE
SET
], rotate [CH] to select “TX
memory” then push [ENT], also selects the transmit
memory screen.
memory screen.
e Rotate [CH] to select the selected memory chan-
nel to be read.
r Push [ENT] to display the memory contents.
t Operate as follows:
➥When reading the memory contents only;
• Push [MODE
SET
] to return to DSC watch
mode.
➥When transmitting the memory contents;
• Push and hold [CALL] for 1 sec.
➥When clearing the memory contents;
• Push and hold [CE] for 1 sec.
* * * * * * T X m e m o r y * * * * * * *
- - - - - - I n d i v i d u a l - - - - - -
T o : 9 8 7 6 5 4 3 2 1
C a t e g o r y : R o u t i n e
C a l l F r e q : T X 2 1 8 7 . 5 k H z
R X 2 1 8 7 . 5 k H z
T r a f f i c : T e l e p h o n y
T X 2 1 3 4 . 0 k H z
R X 2 1 3 4 . 0 k H z
D E L
C a l l
* * * * * * T X m e m o r y * * * * * * *
- - - - - - - - S e l e c t - - - - - - - -
0 : I n d i v i d u a l 9 8 7 6 5 4 3 2 1
1 :
2 :
3 :
4 :
5 :
Ç
O K
S E L