Hitachi 35ux60b, 35tx10b Benutzerhandbuch
USING THE GENIUS REMOTE TO LEARN ADDITIONAL
FUNCTIONS FOR CLU-850GR
FUNCTIONS FOR CLU-850GR
58
If the storing was not done correctly, or the codes are too long to learn, or no more
codes can be stored in memory due to memory overflow, the LEARN indicator and
READY indicator will flash on and off.
codes can be stored in memory due to memory overflow, the LEARN indicator and
READY indicator will flash on and off.
Set the LEARN/USE mode select switch on the back of the Genius Remote to "USE"
and check that the button to which the code is stored operates correctly. If it does not
operate correctly, repeat from step 1.
operate correctly, repeat from step 1.
Repeat steps 3 to 5 to store other keys.
To clear the stored codes from the USER mode
Set the MULTI-PAGE select switch to the USER mode and LEARN/USE mode select
switch to "LEARN". Then, press the POWER and the MUTE buttons simultaneously for
3 seconds. The "READY" and "LEARN" LEDs will light together. All MULTI-PAGE KEYS
with codes are reset to their initial states.
Set the MULTI-PAGE select switch to the USER mode and LEARN/USE mode select
switch to "LEARN". Then, press the POWER and the MUTE buttons simultaneously for
3 seconds. The "READY" and "LEARN" LEDs will light together. All MULTI-PAGE KEYS
with codes are reset to their initial states.
To remember stored codes, it is convenient to paste the labels (user's label) provided
on the buttons for the USER page. If the correct labels are not provided, it is possible to
write these letters on an empty label with a ballpoint pen.
on the buttons for the USER page. If the correct labels are not provided, it is possible to
write these letters on an empty label with a ballpoint pen.
Example of User's Labels
NOTE:
1. To operate your TV, be sure to point the Genius Remote at the remote sensor on the
television. To operate other electronic equipment like a VCR, point the remote at the sensor
on the device.
2. Refer to the instruction manual of the VCR for operation on the buttons exclusively for
the VCR.
3. Be sure to keep the original remote transmitter even after storing its codes in the Genius
Remote Control.
4. If the Genius Remote is left with its batteries removed, the learned codes in its memory
are erased and will have to be reprogrammed into the memory.
5. The Genius Remote Control may not be able to learn certain special remote codes.
1. To operate your TV, be sure to point the Genius Remote at the remote sensor on the
television. To operate other electronic equipment like a VCR, point the remote at the sensor
on the device.
2. Refer to the instruction manual of the VCR for operation on the buttons exclusively for
the VCR.
3. Be sure to keep the original remote transmitter even after storing its codes in the Genius
Remote Control.
4. If the Genius Remote is left with its batteries removed, the learned codes in its memory
are erased and will have to be reprogrammed into the memory.
5. The Genius Remote Control may not be able to learn certain special remote codes.
CAUTION ON BATTERIES:
1. The Genius Remote Control is working when the LEARN indicator lights up when a
button is pressed.
2. When you press a button and the learn indicator will not light up or if the operation is
extremely slow, this is an indication that the batteries should be replaced.
3. Even if the batteries seem dead, do not remove them until you have replacement
batteries ready to put in. The codes stored in memory will be erased in a few minutes
without power. When replacing batteries, prepare the new ones first.
1. The Genius Remote Control is working when the LEARN indicator lights up when a
button is pressed.
2. When you press a button and the learn indicator will not light up or if the operation is
extremely slow, this is an indication that the batteries should be replaced.
3. Even if the batteries seem dead, do not remove them until you have replacement
batteries ready to put in. The codes stored in memory will be erased in a few minutes
without power. When replacing batteries, prepare the new ones first.