Roland SJ-645EX Benutzerhandbuch
105
Chapter 7: What to Do If...
Meaning
A motor error occurred.
The air temperature where installed is lower than
the ambient temperature at which the unit can
operate (approx. 5°C (41°F) or more lower).
the ambient temperature at which the unit can
operate (approx. 5°C (41°F) or more lower).
The air temperature where installed is higher
than the ambient temperature at which the unit
can operate (approx. 40°C (104°F) or more
higher).
than the ambient temperature at which the unit
can operate (approx. 40°C (104°F) or more
higher).
The [SETUP] key was pressed even though no
media is loaded.
Setup was performed with no media at the
correct location.
media is loaded.
Setup was performed with no media at the
correct location.
[SHEET TYPE] is set to [OPAQUE], but
transparent media was loaded.
transparent media was loaded.
An attempt was made to load media that is too
small.
small.
The reflective tape is dirty.
The [SETUP] key was pressed with the pinch
rollers up.
The pinch rollers were raised during setup.
rollers up.
The pinch rollers were raised during setup.
The print head was returned to its standby
position to be capped, canceling current printing
job.
Because emergency stop was effected more than
10 min.
position to be capped, canceling current printing
job.
Because emergency stop was effected more than
10 min.
Continuous operation caused the pump motor to
become hot, so operation was paused to prevent
damage to the motor.
become hot, so operation was paused to prevent
damage to the motor.
• A problem occurred that resulted in a error that
cannot be canceled.
• Correct operation became impossible because
an error occurred.
• The useful life has ended for a component that
must be replaced by a service technician.
cannot be canceled.
• Correct operation became impossible because
an error occurred.
• The useful life has ended for a component that
must be replaced by a service technician.
A problem was found in the data received.
The head height and the loaded media do not
match.
match.
Action
Recovery from this problem is impossible.
Use the POWER key to switch the power off and
back on again.
After rectifying the cause of the error (a media
jam or the like), switch on the power.
Do not leave the unit with the print-head carriage
not in standby position.
Use the POWER key to switch the power off and
back on again.
After rectifying the cause of the error (a media
jam or the like), switch on the power.
Do not leave the unit with the print-head carriage
not in standby position.
Recovery from this problem is impossible. Use
the [POWER] key to switch the power off. First
raise the temperature of the area where installed,
then switch on the power.
the [POWER] key to switch the power off. First
raise the temperature of the area where installed,
then switch on the power.
Recovery from this problem is impossible. Use
the [POWER] key to switch the power off. First
drop the temperature of the area where installed,
then switch on the power.
the [POWER] key to switch the power off. First
drop the temperature of the area where installed,
then switch on the power.
Load media at the correct location and press the
[SETUP] key again (see "2-2 Loading Media").
[SETUP] key again (see "2-2 Loading Media").
When using transparent media, set [SHEET
TYPE] to [CLEAR] (see "4-5 Using Transparent
Media").
TYPE] to [CLEAR] (see "4-5 Using Transparent
Media").
Replace with media of loadable size.
Wipe off the grime on the reflective tape, then
perform setup again.
perform setup again.
Move the loading lever toward "LOAD" and
lower the pinch rollers, then press the [SETUP]
key (see "2-2 Loading Media").
lower the pinch rollers, then press the [SETUP]
key (see "2-2 Loading Media").
Turn power off by pressing [POWER] key to
reset.
Interrupted printing is not resumed. Repeat
printing from the beginning.
reset.
Interrupted printing is not resumed. Repeat
printing from the beginning.
Press any key to cancel the message.
Allow the unit to stand for about 40 minutes,
then resume operation.
Allow the unit to stand for about 40 minutes,
then resume operation.
Check the number shown on the display, then
press the [POWER] key to switch off the power.
After you switch off the power, inform your
authorized Roland DG Corp. dealer or service
center of the number that appeared on the
display.
press the [POWER] key to switch off the power.
After you switch off the power, inform your
authorized Roland DG Corp. dealer or service
center of the number that appeared on the
display.
Make sure the cable is attached securely.
Change the head height to the specified height
and press the [ENTER] key.
and press the [ENTER] key.
Messages
MOTOR ERROR
TURN OFF POWER
TEMPERATURE
IS TOO LOW
TEMPERATURE
IS TOO HIGH
SHEET SET ERROR
SET AGAIN
PINCHROLL ERROR
LOWER PINCHROLL
AVOIDING DRY-UP
TURN OFF POWER
CANCELED FOR
PROTECTING MOTOR
SERVICE CALL
No: * * * *
DATA ERROR
CANCELING ...
SET HEAD HEIGHT TO
- - -
7-2 What to Do If an Error Message Appears