Outback Power Systems vfx 3232m Benutzerhandbuch
Copyright 2003
OutBack Power Systems, Inc.
FX & VFX Series Inverter/Charger System Installation & Programming Manual
19009 62
nd
Ave NE, Arlington WA 98223 USA
900-0027-1
Tel 360 435 6030 Fax 360 435 6019
Rev 7.2
08/26/05
Page 49
MATE SCREENS
SELL MENU
The SELL section of the STATUS menu has only one screen. This screen gives a number that refers to a reason the FX would stop
selling. OutBack Power Systems technicians use this number to quickly understand what the FX thinks is happening. The system user
should not be concerned about this number unless they are experiencing many unknown grid disconnects and they need
troubleshooting help. This screen is only operational with “Grid-Tie” FX’s.
selling. OutBack Power Systems technicians use this number to quickly understand what the FX thinks is happening. The system user
should not be concerned about this number unless they are experiencing many unknown grid disconnects and they need
troubleshooting help. This screen is only operational with “Grid-Tie” FX’s.
MAIN----------------
6:54:42P
SUM STATUS SETUP ADV
↓
STATUS--------------
choose product:
choose product:
FX
MX
↓
STATUS/FX/PAGE1-----
choose category:
choose category:
MODES METER BATT PG2
↓
STATUS/FX/PAGE2-----
choose category:
choose category:
PG1 ERROR
WARN
PG3
↓
STATUS/FX/PAGE3-----
choose category:
choose category:
PG2 DISCON SELL MAIN
↓
STATUS/FX/SELL---P00
stop sell
stop sell
14
reason
STATUS
STATUS
PORT
The MAIN screen is where the menu system starts. The four words in the bottom line of the display
correspond to the four buttons located below the display. The word in BOLD on the bottom line
indicates the selection used to advance the display to the next screen. Pressing the left two buttons
simultaneously from anywhere in the menu will return you to this screen.
correspond to the four buttons located below the display. The word in BOLD on the bottom line
indicates the selection used to advance the display to the next screen. Pressing the left two buttons
simultaneously from anywhere in the menu will return you to this screen.
Allows selection of the product type:
<FX>
<FX>
FX inverter/charger system
MX
MX60 PV MPPT charge controller
MODES
Status and allows adjustment of Inverter, AC input, Charger, Aux, and EQ
METER
Provides the AC voltages and currents of the FX
BATT
Provides the battery voltage and charger set points and timers
<PG2>
Displays additional sections – ERRORS, WARNINGS and PG3
PG1
Returns to page 1 of the STATUS section
ERROR
Displays the different causes for errors and qualifies each cause with a Yes or No
WARN
Displays the different causes for warnings and qualifies each with a Yes or No
<PG3>
Displays additional sections – reason for last DISCONNECT and SELL
PG2
Displays additional sections – ERRORS, WARNINGS and PG3
DISCON
Displays the reason that the FX last disconnected from the AC source
<SELL>
Displays the code related to the reason for the last disconnection while selling
MAIN
Returns the user to the MAIN menu
The STOP SELL REASON displays a numerical value that indicates a reason that the FX stopped
selling to the utility grid. It could indicate that the utility grid’s voltage or frequency is out of the
acceptable ranges or that the utility grid failed altogether. This screen is used for troubleshooting by
OutBack Power Systems technicians. Selecting STATUS returns the user to the beginning of the
STATUS menu. Selecting PORT selects the next FX on the HUB.
selling to the utility grid. It could indicate that the utility grid’s voltage or frequency is out of the
acceptable ranges or that the utility grid failed altogether. This screen is used for troubleshooting by
OutBack Power Systems technicians. Selecting STATUS returns the user to the beginning of the
STATUS menu. Selecting PORT selects the next FX on the HUB.