Omron r53 Benutzerhandbuch

3.4 Using the Memory Function

The unit automatically stores up to 60 sets of measurement
values (blood pressure and pulse rate).
It can also calculate an average reading based on the
measurements from the last three readings taken within 10
minutes. If there are only two readings in memory for that
period, the average will be based on two readings. If there is
one reading in memory for that period, the average will be
based on one reading.
Notes:
• If the memory is full, the monitor will delete the oldest

readings.

• When viewing the reading taken without setting the date and

time, “-:--” is displayed instead of the date and time.

To View the Average Value

To View the Readings Stored in Memory

To Delete All the Values Stored in Memory

Note: You cannot partially delete the stored readings.

4.1 The Icons and Error Messages

Note: The irregular heartbeat symbol (

) may also be displayed

with error messages.

4.2 Troubleshooting

4.3 Maintenance

To protect your unit from damage, please observe the
following:

• Do not subject the main unit and the cuff to

extreme temperatures, humidity, moisture or
direct sunlight.

• Do not disassemble the unit.
• Do not subject the unit to strong shocks or

vibrations (for example, dropping the unit on the
floor).

• Do not use volatile liquids to clean the main unit.
• Do not wash the cuff or immerse it in water.
• Do not use petrol, thinners or similar solvents to

clean the cuff.

• Do not carry out repairs of any kind yourself. If a

defect occurs, consult your OMRON retail outlet
or distributor as mentioned on the packaging.

• The unit should be cleaned with a soft, dry cloth.
• Use a soft, moistened cloth and soap to clean

the cuff.

• Keep the unit in its storage case when not in

use.

• Fold the cuff into the storage case.

Do not store the unit in the following situations:

• If the unit is wet.
• Locations exposed to extreme temperatures,

humidity, direct sunlight, dust or corrosive
vapours.

• Locations exposed to vibrations, shocks or

where it will be at an angle.

Calibration and Service

• The accuracy of this blood pressure monitor has

been carefully tested and is designed for a long
service life.

• It is generally recommended to have the unit

inspected every two years to ensure correct
functioning and accuracy. Please consult your
authorised OMRON dealer or the OMRON
Customer Service at the address given on the
packaging or attached literature.

Note: Subject to technical modification without prior notice.

• This device fulfils the provisions of EC directive 93/42/EEC

(Medical Device Directive).

• This blood pressure monitor is designed according to the European

Standard EN1060, Non-invasive sphygmomanometers Part 1:
General Requirements and Part 3: Supplementary requirements
for electromechanical blood pressure measuring systems.

• This OMRON product is produced under the strict quality system of

OMRON HEALTHCARE Co. Ltd., Japan. The Core component for
OMRON blood pressure monitors, which is the Pressure Sensor, is
produced in Japan.

Made in China

Press the Memory button.

Note: If there are no measurements

results stored in the memory, the
screen to the right is displayed.

Press the

button, while the average value is

displayed.

The Memory number
appears for a second
before the pulse rate is
displayed. The newest
set is numbered “1”.

Press the

button repeatedly to view the

readings stored in memory.

When the memory symbol (

) appears, first press

the

button. Then while holding it down, press the

START/STOP button simultaneously for about 2 - 3
seconds.

Error Display

Cause

Remedy

Irregular heartbeats
are detected.

Remove the wrist cuff. Wait
2 - 3 minutes and then take
another measurement.
Repeat the steps in section
3.3. If this error continues to
appear, contact your doctor.

Movement during
measurement.

Carefully read and repeat the
steps in section 3.3.

Blink

The batteries are
low.

You should replace them with
new ones ahead of time.
Refer to section 2.1.

Lit

The batteries are
exhausted.

You should replace them with
new ones at once.
Refer to section 2.1.

Wrist cuff not
applied correctly.

Apply the wrist cuff correctly.
Refer to section 3.1.

Movement during
measurement.

Repeat Measurement while
remaining still and refraining
from talking during the
measurement.
Refer to section 3.3.

Wrist cuff not
applied correctly, or
movement during
measurement.

Apply the wrist cuff correctly
and repeat measurement
while remaining still and
refraining from talking during
the measurement.
Refer to section 3.1 and 3.3.

Device error.

Contact your OMRON retail
outlet or distributor.

Alternating
date/time
display

First

Second

4. Troubleshooting and Maintenance

Problem

Cause

Remedy

The reading is
extremely low
(or high).

The wrist cuff is not
at heart level.

Measure while in the
correct posture.
Refer to section 3.2.

The cuff is not
wrapped snugly
around the wrist.

Wrap the cuff correctly.
Refer to section 3.1.

The arms and
shoulders are
tense.

Relax and try taking the
measurement again.
Refer to section 3.3.

Movement or
talking during
measurement.

Remain still and do not
talk during Measurement.
Refer to section 3.3.

Wrist cuff pressure
does not rise.

Air is leaking from
the wrist cuff.

Consult your OMRON
retail outlet or distributor.

Wrist cuff deflates
too soon.

The wrist cuff is
loose.

Apply the cuff correctly so
that it is firmly wrapped
around the wrist. Refer to
section 3.1.

The blood pressure is different
each time. The reading is
extremely low (or high).

Blood pressure readings
constantly vary with time
of day and how relaxed
you are. Take several
deep breaths and try to
remain relaxed before
taking a measurement.

The unit loses
power during
measurement.

The batteries are
exhausted.

Replace the batteries with
new ones.
Refer to section 2.1.

Nothing happens
when you press
the buttons.

The batteries have
been inserted
incorrectly.

Insert the batteries with
the correct (+/-) polarity.
Refer to section 2.1.