culligan preferred series Benutzerhandbuch

SPECIFICATIONS
Operating Pressure Range: 10 - 125 psi (0.7 bar - 8.6 bar)
Operating Temperature Range: 35 - 100°F (2 - 38°C)
Service Flow Rate: 0.5 gpm (1.9 Lpm)
Capacity:  750 gal. (2,839L) Preferred 150

1000 gal. (3,785L) Preferred 250

300 gal. (1,135L) Preferred 350

For cold water use only

Note that some states require licensed installers, and some
states prohibit the use of saddle valves.

Culligan recommends that Preferred Series Drinking Water
Filters be installed with a faucet dedicated to dispensing only
filtered water. Such a faucet is available from Culligan by
ordering P/N 01-0035-37*. Refer to the plumbing schematic
shown in Figure 1 when completing this type of installation.
Other recommended applications include point-of-use 
drinking water coolers, refrigerators, and ice makers.

®

NSF's Certification Program

is accredited by the Dutch

Council for Accreditation

NSF's Certification Program

is accredited by the American

National Standards Institute

System Tested and Certified by NSF
International against NSF/ANSI
Standards 42 and 53 for the reduction of:

Standard No. 42:  Aesthetic Effects
      Chemical Unit
 

Taste and Odor Reduction

 

Chlorine Reduction

      Mechanical Filtration Unit
 

Particulate Reduction

 

99.9+% reduction of  particles

 

one-half  micron and larger in size

Standard No. 53:  Health Effects
      Chemical Reduction Unit
 

Lead Reduction

 

VOC Reduction (350 Only)

      Mechanical Filtration Unit
 

Turbidity Reduction

 

Cyst Reduction

 

Asbestos Reduction

Check for compliance with state and local laws and regulations.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system.  Systems certified for cyst reduction may be used on 
disinfected water that may contain filterable cysts.

This filter system is supplied with fittings which are
designed for use with 1/4 inch O.D. polyethylene tubing:
available from Culligan by ordering P/N 00-4021-84*.
1. Select a location for the filter assembly which:

• Provides a solid mount for the filter head.
• Allows a minimum 2 inches (5 cm) of clearance

under the cartridge.

• Allows space for inlet and outlet water line connections.

Note: The filter must be mounted vertically.

2. Provide an inlet water supply for the filter by tapping

the cold water line. This connection should accom-
modate 1/4 inch O.D. polyethylene tubing and must
comply with state and local laws and regulations.

3. Install the faucet or dispensing device according to the

instructions provided with the device.

4. Refer to Figure 2 to determine the best filter bracket 

position to accommodate the water connections.

5. Install the 0.5 gpm flow restrictor fitting into the outlet

port on the filter head using Teflon tape.
Note: The restrictor is built into one of the elbow fittings.

6. Install the remaining 1/4 inch tubing fitting into the fil-

ter head inlet using Teflon tape.

7. Mount the filter head using the screws and washers 

provided.

8. Connect the inlet and outlet tubing to the inlet and

outlet fittings of the filter. Double check the water
connections to be sure that water will follow the
direction-of-flow arrow on top of the head; water 
supply to inlet fitting, outlet fitting to faucet.

9. Install the filter cartridge as detailed in Figure 3.
10.Flush the cartridge for three minutes to purge the

system of air.

12-3/4” (32.4 cm)

17-3/4” (45.1 cm)

20” (50.8 cm)

Rev. D 01/06/03

DCO# 5378

Validated by WQA according to NSF/ANSI 42

and 53 for the claims listed by NSF International

as verified and substantiated by test data.

Figure 1

*Not tested or certified by NSF.