ICOM bc-119n Benutzerhandbuch

R

WARNING! To reduce the risk of injury,

charge only specified Icom Ni-Cd, Ni-MH
or Li-Ion rechargeable battery packs.
Other types of battery packs/cases may
burst, causing damage and personal
injury.

R

USE INDOORS ONLY! NEVER expose

the charger to rain, snow or any liquids.

NEVER let metal, wire, etc. touch any
internal part of the charger.

NEVER incinerate used batteries. This
may cause an explosion.

NEVER use the charger when it is covered
by objects which impede heat dispersal.

Place the charger in a secure place to
avoid inadvertent use by children.

AVOID charging in conditions of extreme
cold 

(under 10°C; +50°F)

or extreme heat

(over +40°C; +104°F)

. Batteries may not

charge under extreme temperatures.

Keep the charger away from TV sets or
radios to prevent interference.

R

NEVER attempt to charge alkaline or

dry cell batteries. They may burst causing
damage and personal injury.

Make sure battery and charger con-
tacts are always clean, otherwise bat-
teries may not fully charge.

SAVE THESE INSTRUCTIONS! These
instructions contain important safety and
operating details for the BC-119N.

An appropriate desktop charger adapter
must be purchased separately to charge
your Icom battery packs.

In order to get the maximum life out of your
Ni-Cd batteries:
1. Avoid overcharging— batteries must be

removed from the charger to stop
charging. Batteries should not be
charged for more than 15 hours after
the LED indicator turns green.

2. Use the batteries until they become

almost completely exhausted under
normal conditions.

If your batteries seem to have no
capacity even after being fully charged,
completely discharge them, then fully
charge them again. If they still do not
retain a charge 

(or very little)

, new bat-

teries must be purchased.

There are 2 desktop charger adapter types
for the BC-119N. One has a PCB, the other
does not. The non-PCB types require an
additional PCB 

(AD-75 or AD-88)

. For some

versions, the AD-75 or AD-88 is already in-
stalled in the BC-119N. 

D

D

Connect the plugs of an appropriate desk-
top charger adapter and the BC-119N, then
installed the adapter with the screws 

(sup-

plied with the adapter)

. For some versions, the

desktop charger adapter is already installed.

NOTE: Some of the PCB type desktop
charger adapters 

(incl. AD-75/88)

do not

need connection of the 3-pin connector.

The connection is required only for the
installing adapter that is compatible with
charging a Li-Ion battery pack.

D

D

Install the optional AD-75 or AD-88 to the
BC-119N with 4 screws 

(supplied with the AD-

75/AD-88)

, then attach a desktop charger

adapter to the BC-119N. See the trans-
ceiver’s instruction manual for an approved
desktop charger adapter.

Not used
See NOTE below

See NOTE below

INSTRUCTIONS

DESKTOP CHARGER

BC-119N

Thank you for purchasing the BC-119N

DESKTOP CHARGER

. The BC-119N charges

a Ni-Cd or Ni-MH battery pack in approx.
1–2 hrs., or a Li-Ion battery pack in
approx. 2–3 hrs.

Please read these instructions thoroughly
before operating the BC-119N.

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan

A-6099D-1EX-

q

Printed in Japan

© 2001 Icom Inc.

ATTACHING A DESKTOP CHARGER ADAPTER

Icom, Icom Inc. and 

are registered trademarks of Icom Incorporated (Japan) in the United States, United

Kingdom, Germany, France, Spain, Russia and/or other countries.

The Ni-Cd battery that you have

purchased is recyclable. At the
end of its life, under various state
and local laws, it may be illegal to
dispose of this battery into the

municipal waste stream. Call 1-800-822-8837 for
battery recycling options in your area or contact
your dealer.

Some versions of the BC-119N
which display the “CE” symbol on
the serial number comply with the
essential requirements of the
89/336/EEC directive for
Electromagnetic Compatibility.

This compliance is based upon the harmonised
CENELEC generic standard EN50 081-1: 1992
and EN50 082-1: 1991.

R

About the 3-pin connector:
When you replace the desktop charger adapter
from the Li-Ion compatible type to non-compatible type, fix
the 3-pin connector to the bottom of the charger with adhe-
sive tape, etc., to prevent catching or touching the 3-pin con-
nector’s terminals with the adapter’s leads, etc.

Fix the connector with
adhesive tape, etc.