Lennox mpb-40 Benutzerhandbuch
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Printed in U.S.A. © LENNOX HEARTH PRODUCTS 2005
P/N 750,199M REV. A 04/2006
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design,
materials, specifi cations, prices and the discontinuance of colors, styles and products. Consult
your local distributor for fi replace code information.
materials, specifi cations, prices and the discontinuance of colors, styles and products. Consult
your local distributor for fi replace code information.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
1110 West Taft Avenue • Orange, CA 92865
Figure 3
- GLASS DOOR ADJUSTMENT
Top Flange on Glass Door
Bottom Vee-fl ange Glass Door
Glass Door Latch
Glass Door
Firebox Floor
Some models will have a
modesty panel in the control
compartment (in front of
the valve). The appearance
will vary from the example
shown below.
modesty panel in the control
compartment (in front of
the valve). The appearance
will vary from the example
shown below.
Figure 5
- COMPLETED INSTALLATION
3. Remove the arched screen doorframe from packaging, then install it as
follows:
a. Locate slots on each side of fi replace.
b. Position the top of the doorframe above the top of the glass door
b. Position the top of the doorframe above the top of the glass door
assembly (centered and approximately 1” above glass door assem-
bly). See Figure 4.
bly). See Figure 4.
Note: The bottom of the doorframe should be held slightly away as shown
in Figure 4. Swing the bottom of the doorframe inward aligning the sides
of the doorframe between the glass door and fi replace chassis and tabs
on doorframe aligning into slots on fi replace. Swing the bottom of the
doorframe in, then push down to ensure engagement.
in Figure 4. Swing the bottom of the doorframe inward aligning the sides
of the doorframe between the glass door and fi replace chassis and tabs
on doorframe aligning into slots on fi replace. Swing the bottom of the
doorframe in, then push down to ensure engagement.
4. Ensure that the latch(es) below the door are engaged with the door’s vee-
fl ange and fully closed before operating the fi replace (see Figure 3).
5. (Units with Modesty Panels) Reinstall modesty panel, ensuring all wires
are securely connected.
6. If applicable, reinstall the top louver assembly, radiant panels or hood.
7. Reinstall or close the bottom louver or radiant panel.
7. Reinstall or close the bottom louver or radiant panel.
Install Top of
Door fi rst per
Instruction #3
Door fi rst per
Instruction #3
Swing the bottom of the doorframe inward, then push into place
Doorframe
Figure 4
- INSTALL DOORFRAME
Bustles
Figure 2
- Remove Bustles
Lift Bustles Up
And Off
And Off
Only Some Models
Have Bustles
Have Bustles
2. Ensure the glass door assembly on the fi replace is properly aligned as
follows:
a. Open or remove lower compartment door (refer to Homeowner’s
Manual provided with appliance).
Note: Units with Modesty Panels - Remove the modesty panel as follows:
Lift the modesty panel by the tab on the panel’s right end, pull the right end
of the panel away from cabinet and then pull the panel diagonally out of the
corner post slots on the left side of the unit. Remove the modesty panel
carefully, so that none of the wires become loose or disconnected.
Lift the modesty panel by the tab on the panel’s right end, pull the right end
of the panel away from cabinet and then pull the panel diagonally out of the
corner post slots on the left side of the unit. Remove the modesty panel
carefully, so that none of the wires become loose or disconnected.
b. Open the latch(es) at the bottom of the glass door assembly as
shown in Figure 3 (refer to Homeowners Manual).
c. Adjust glass door so that it is evenly spaced and aligned to the
fi replace chassis on both sides. See Figure 3.
d. Fasten the latch(es). Ensure that the latch(es) are engaged with
the door’s vee-fl ange and fully closed. See Figure 3.
Modesty Panel
2