DYMO rhinopro 1000 Benutzerhandbuch

DYMO 1000

DYMO 1000

Insert five size AA alkaline or
nickel-cadmium re-chargeable
batteries, observing the polarity
markings.
Re-chargeable batteries must be
charged externally before use.

Connect the AC
adaptor plug here. Use
only the recommended adaptor.
Plugging in the AC adaptor
disconnects the batteries.
Note: Re-chargeable batteries will
not be charged.

Cover
slides
off.

Ensure tape and ribbon is
taught across mouth of
cassette and tape passes
between
the guide posts
before installing.

Lift cassette
straight up
and out.

Push firmly
until cassette
clicks into
place.

Print head

TAPE

CASSETTE

Label
cutter –
press to
cut off
printed
label.

Make sure that
this switch is set
to the RIGHT
before installing
the cassette. A
notch in the
cassette will fit
over the switch
when it is set
correctly.

To remove the door, press in
where shown below then swing
the door open and lift it away.
When re-fitting, hold the door at
the angle shown below and
engage the tabs on the door in
the slots in the case.
Now close the door, ensuring
that the lever engages with the
ramp on the door as it closes.

Ensure this lever
engages with ramp on
door when closing.

Press
here to
open

➭

➋

➧

Use a ball pen or
pencil to hold down
    interlock button.

➧

➍

Check and clean
print head and
pinch roller
regularly using
cotton bud and
alcohol ONLY.

➍

Use a cotton
bud and alcohol
to clean both
sides of cutter
blade regularly.

➌

Press

➬

➊

Ensure tape and ribbon are
positioned as shown between
print head and pinch roller.

        DISPLAYED

$ ¢   £ Fr ¥

$

¢   £ Fr ¥

@ & #

:

;

@ & #

:

;

"

< >

±

=

"

< >

±

=

\

÷

X % *

\

÷

X % *

°

R

°

C

T

°

®

© ™

☎

°

2

3

2

3

1

/

2

2

3

2

3

1

/

2

µ Ω

µ Ω

1

.. .

2

.. .

3

.. .

4

.. .

5

.. .

!

6

.. .

➞

Æ Å Ç Œ Ø

Æ Å Ç Œ Ø

æ å ç œ ø

æ

å ç œ ø

àˠѠÕ

Ã

Ë Ñ Õ

ã ë ñ õ

ã

ë ñ õ

â ê

î

ô û

â

ê

î

ô û

ß ¿

¡

● ★

ß

¿

¡

● ★

Á É

Í Ó Ú

Á

É

Í Ó Ú

á é

í

ó ú

á

é

í

ó ú

ì

ò

!

ì

ò

!

International characters
You can create international characters by combining a letter
and a diacritical (accent). Diacriticals available on the  keyboard
are ´ ` ¨ and ^. To add a diacritical to a character, enter the
character first, followed immediately by the diacritical. For
example, press ‘E’ followed by ‘´’ to get é.
To add a diacritical to an existing character, use 

<

 or 

<

 to

place the cursor under the character to be changed, then press
the appropriate diacritical key.

Symbols
Pressing 

SYM

 changes the display to show symbols and

special characters, some of which are not available direct from
the keyboard. The display will show:

(or

where available).

Each letter selects a line of five symbol characters, as shown in
the table below. Note that some of the more complex printed
symbols are represented by simpler symbols in the display.
Press 

DEL

 to cancel or press the letter key required.

Use 

<

 or 

<

 to select a symbol. Press 

SYM

 again to place the

symbol in the label, or press 

PRINT

1, 

2, 

3

...n

  to place it and print the label.

No display
• check machine is on
• replace discharged batteries

or use the AC adaptor

• check AC adaptor plugged

in and switched on.

No printing or poor text
• replace discharged batteries

or use the AC adaptor

• check tape cassette

installed correctly and tape
not kinked

• replace the tape cassette.
No response to print key
• label length too short for text

– press 

<

 until >

disappears or clear fixed
length

•

in display indicates a

printer jam. Printing will stop
and the display return to
normal. Open the cassette
compartment and free the
jam.

•

 flashing in the display

indicates low battery volts.
Replace discharged
batteries or use the AC
adaptor.

1

/

2

") cassettes

Black/Clear

45010

Blue/Clear

45011

Red/Clear

45012

Black/White

45013

Blue/White

45014

Red/White

45015

Black/Blue

45016

Black/Red

45017

Black/Yellow

45018

Black/Green

45019

15030

15010

40030

Print contrast — may be adjusted by pressing 

SYM

 followed by the

space key to display five contrast symbols. Use 

<

 or 

<

 to select a

symbol. Press 

SYM

 again to confirm the setting. The contrast level will

revert to the mid-setting when the Labelmaker is turned off and on
again.

Note: Rows
p, q and r
where
available.

M

➞

➞

➞

➞

➞

This product is designed to conform with the
following international standards:

EN 60950

Specification for safety

IEC 950

of information technology

UL 1950

equipment including electrical
business equipment

EN 55022

Specification for limits and

Class B

methods of measurement of
radio interference
characteristics of information
technology equipment.

FCC pt15

Federal communications

Sub pt B

commission radio frequency

Class B

emissions.

Written by

DAW Publications, Cambridge