Lindy 32450 Benutzerhandbuch
Specifiche Tecniche
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - SECOND EDITION (JAN 2005)
For Commercial Use
Tested to Comply with
FCC Standards
Tested to Comply with
FCC Standards
Direttiva Europea EMC 89/336/EEC Marchio CE
Questa apparecchiatura è conforme alle specifiche CE menzionate nella Direttiva Europea 89/336/EC a agli
Standards EN55022 e EN55024
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B Digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
y Reorient or relocate the receiving antenna
y Increase the separation between the equipment and receiver
y Connect the equipment into an outlet on a circuit different from that to which the receiver is
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
y Reorient or relocate the receiving antenna
y Increase the separation between the equipment and receiver
y Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
y Consult the dealer or an experienced technician for help
You are cautioned that changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
compliance could void your authority to operate the equipment.
Modello
IPower Switch 4 LITE
Art. 32450
Art. 32450
IPower Switch 8 LITE
Art. 32451
Art. 32451
Porta Remote Access
Ethernet 10Base-T, RJ-45
Prese di alimentazione IN/OUT
1x IEC-Plug / 4x IEC-Socket
2x IEC-Plug / 8x IEC-Socket
Parametri di alimentazione Ingresso
230V AC 2300VA (10A@230V)
230V AC 2x2300VA, 2x(10A@230V)
Parametri alimentazione Uscite
Max. 8A per ogni Uscita, 10A totale
Max. 8A per ogni uscita, 2x10A totali
Temperatura Operativa
+5°C ... 40°C, esclusivamente per uso in interni
Umidità
5 … 85% rel. non condensata
Misure (HXLXP), Peso
44.5 (1U) x 441 x 63 mm, 1.4kg
44.5 (1U) x 788 x 63 mm, 2.3kg
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - SECOND EDITION (JAN 2005)
For Commercial Use
Tested to Comply with
FCC Standards
Tested to Comply with
FCC Standards
IPower Strip LITE
Manuale dell’utente
Italiano
(Versione 8/2004, Versione Firmware 1.18; la versione fornita può essere più recente)
Modello 1 IN / 4 OUT: LINDY Art. 32450
Modello 2 IN / 8 OUT: LINDY Art. 32451
Modello 2 IN / 8 OUT: LINDY Art. 32451
www.LINDY.com