Panasonic DMREZ28 Bedienungsanleitung

51

RQT9118

 Tips

To browse through the list
Press [1, 2 CH].

You can restart auto channel setting for digital terrestrial channels 
if set up (

➔ 11) fails for some reason.

However, if you perform “Auto-Setup Restart”, all channel settings 
and all created profiles are deleted.

Press [w] to select “Yes”, then press [OK].

 Tips

You can also use the following method to restart Auto-Setup.
(All the settings except for the ratings level, ratings password, 
Owner ID and Clock return to the factory preset. The timer 
recording programmes are also cancelled.)

 

When the unit is turned on and stopped, press and hold 

[2 CH] and [CH 1] on the main unit at the same time for 
about 5 seconds.
Auto-Setup screen appears.

•

You can set channels manually if the DVB Auto-Setup could not 
complete successfully.

DVB Manual Tuning

Signal Strength

10

Prog.

Quality

Channel

Service Name

Net ID

TS ID

Signal Quality

10

Frequency

0

MHz

Channel System

0

RETURN

START SCAN

CHANNEL

United Kingdom

DVB CH21                       474.0

1. Press [e, r] to select the channel you want to set.

Select the channel by checking the signal strength and 
signal quality displays.
[Refer to “Signal Condition” (

➔ right) for signal strength and 

signal quality.]

2. Press [OK] to start scan.
The set channel is displayed in the table.

Signal Strength

 

Signal Quality

Frequency

MHz

Channel System

1         22        BBC ONE Wales     12290      514      7
2         22        BBC 2W                  12290      514      7
3         22        BBC THREE           12290      514      7

RETURN

START SCAN

CHANNEL

DVB Manual Tuning

3 services found.

10

10

0

0

United Kingdom

DVB CH21                       474.0

Prog.

Quality

Channel

Service Name

Net ID

TS ID

3. Press [EXIT] and press [1, 2 CH], check that applicable 

–

You can search for newly added digital terrestrial channels to 
receive. 

The unit starts searching for newly available digital terrestrial 
channels. This takes about 5 minutes.
The bar over the table shows you the search progress. 
At the end of the search, the number of found new digital 
stations appears.
“No new services found.”, is displayed when 
no new services can be found. 

 Tips

To cancel in middle
Press [RETURN].
The channels found before stopping are not saved.

–

–

–

You can check the quality and strength of digital broadcast signals.
Realign the aerial if you are receiving a poor signal.
When “Signal Condition” is displayed in grey and cannot be 
selected:
1  Press [EXIT] to exit the screen.
2 Press 

[1, 2 CH] to select a digital channel. “D” appears on the 

unit’s display.

3  Display the Setup menu again.

The quality and strength of the signal are shown.
Press [1, 2 CH] to select the other channel.

Below 2 (display red)

The signal quality is so poor that there may 
be interference in the pictures and sound.

2–5 (display orange)

The signal quality is basically adequate, 
but brief interference in the pictures and 
sound is possible in isolated case.

Over 5 (display green) Optimum picture and sound quality.

The display for signal strength is grey. “0” means signal strength 
0%, “10” means signal strength 100%.
If the signal is too strong, the display will change from grey to red.
Reduce the signal amplification at your aerial.

When the signal is weak:

check that the aerial is correctly positioned. 
adjust the aerial reception with “DVB Manual 
Tuning” in the Setup menu (

➔ left).

check that the current digital broadcast 
channel is correctly broadcastin

g.

•

–
–

–

DMR-EZ28-EB _RQT9118-B.indb   51

DMR-EZ28-EB _RQT9118-B.indb   51

2008/04/04   10:32:25

2008/04/04   10:32:25