Mobotix MX-OPT-NPA1-EXT Техническое Руководство
The HiRes Video Company
EN
www
.mobotix.com
HiRes Video Innovations
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its
decentralized concept has made high-resolution video systems cost-efficient.
decentralized concept has made high-resolution video systems cost-efficient.
MOBOTIX AG • D-67722 Langmeil • Tel: +49 6302 9816-103 • Fax: +49 6302 9816-190 • sales@mobotix.com
MX-NPA-Box: Quick Install
Weatherproof PoE Injector
and Network Connector
• Weatherproof power supply, e.g. for an IP camera
• Complete set including mounting supplies
• Complete set including mounting supplies
IEEE 802.3af Network Power Adapter (NPA)
for power supply by external power supply units
and batteries from 12 to 57 V DC
Standard Connection:
Weatherproof PoE Injector
Ethernet Installation Cable and Patch Cable
Installation Instructions
1. Attach the box and insert the cable tie
Attach the MX-NPA-Box at the mounting position with the cable
ports pointing downwards. Remove the box cover (three screws)
and feed the supplied cable tie through the two slots on the
circuit board.
Attach the MX-NPA-Box at the mounting position with the cable
ports pointing downwards. Remove the box cover (three screws)
and feed the supplied cable tie through the two slots on the
circuit board.
2. Prepare the installation cable
Cut the installation cable to size, push it through the cable plug
5 to 7 mm, strip the cable for at least 35 mm and separate
the individual wires of the cable into twisted pairs with 20 mm
shielding. Wrap the shield mesh around the cable sheath 10 mm
wide so that it can rest on the contact plate of the board. The
cable will be fastened with a cable tie later on.
Cut the installation cable to size, push it through the cable plug
5 to 7 mm, strip the cable for at least 35 mm and separate
the individual wires of the cable into twisted pairs with 20 mm
shielding. Wrap the shield mesh around the cable sheath 10 mm
wide so that it can rest on the contact plate of the board. The
cable will be fastened with a cable tie later on.
3. Feed the cable into the box
Replace the sealing plug in the middle, feed the installation
cable through the opening and press the cable plug 5 to 7 mm
into its seat. In order to prevent humidity entering the box, the
rubber sleeve needs to be tight against the cable. Pull the cable
tie tight around the cable shield to provide proper strain relief.
Replace the sealing plug in the middle, feed the installation
cable through the opening and press the cable plug 5 to 7 mm
into its seat. In order to prevent humidity entering the box, the
rubber sleeve needs to be tight against the cable. Pull the cable
tie tight around the cable shield to provide proper strain relief.
4. Connect the cable wires
Use an LSA PLUS wire insertion tool to insert the individual wires
into the LSA terminal. Decide on using either the EIA/TIA-568A
or B wiring standard as in the rest of the building. The color
code sticker in front of the LSA terminal shows both standards.
Use an LSA PLUS wire insertion tool to insert the individual wires
into the LSA terminal. Decide on using either the EIA/TIA-568A
or B wiring standard as in the rest of the building. The color
code sticker in front of the LSA terminal shows both standards.
5. Connect the power supply
Guide the power supply cable through a suitable opening of
the left rubber plug. Use the eight-wire plug for inserting single
wires; use the appropriate cable plug 3 to 5 mm or 5 to 7 mm
for inserting an insulated multi-wire cable. Strip the insulation
of the cable to the power supply unit or battery (12 to 57 V DC)
5 mm at the end and apply wire-end sleeves if using flexible
wires. Attach to the power terminal according to polarity. Mount
the cover back onto the box (torque 0.4 Nm).
Guide the power supply cable through a suitable opening of
the left rubber plug. Use the eight-wire plug for inserting single
wires; use the appropriate cable plug 3 to 5 mm or 5 to 7 mm
for inserting an insulated multi-wire cable. Strip the insulation
of the cable to the power supply unit or battery (12 to 57 V DC)
5 mm at the end and apply wire-end sleeves if using flexible
wires. Attach to the power terminal according to polarity. Mount
the cover back onto the box (torque 0.4 Nm).
6. Attach the patch cable
Remove bayonet catch and the sealing plug of the right port,
insert a MOBOTIX patch cable into the right port and secure it
using the bayonet catch. Only use MOBOTIX patch cables with
integrated sealing ring! A MOBOTIX sealing system for standard
patch cables will be available soon.
Remove bayonet catch and the sealing plug of the right port,
insert a MOBOTIX patch cable into the right port and secure it
using the bayonet catch. Only use MOBOTIX patch cables with
integrated sealing ring! A MOBOTIX sealing system for standard
patch cables will be available soon.
MOBOTIX camera
MOBOTIX patch
cable for PoE
device
Power supply 12 to
57 V DC (power supply
unit or battery with
safety fuse 1.25 A)
Connected
Ethernet
installation
cable
MOBOTIX M25M Secure
MX-M25M-Sec
MOBOTIX MX-NPA-Box
MX-OPT-NPA1-EXT
~20 mm
~35 mm
~15 mm
~10 mm
Shield mesh
Sheath
Pair shield
MX-OPT
-NP
A1-EXT
31.210_EN_V3_01/2014
Weatherproof (IP65)
–30 to +60°C/–22 to +140°F