Select Increments Dash-Pods Benutzeranleitung
Push grommet over each pair of plugs starting with the
large spade first. It’s a tight fit, but it minimizes hole size.
large spade first. It’s a tight fit, but it minimizes hole size.
Feed the spade terminals
through the 7/16” hole
on back of each pod and
push grommet into hole.
through the 7/16” hole
on back of each pod and
push grommet into hole.
Gently pull excess wire from pods.
We recommend sealing any air-
space around wires with glue gun.
We recommend sealing any air-
space around wires with glue gun.
Noteworthy: Backsides of one or both pod(s) may come in contact with heater ducts, which is normal, and the ducts will flex
slightly to accept the pods when they’re screwed in place. This was done to maximize mounting diameter and depth in each pod.
Also, ‘97-’00 models may have the driver side pod contact the headlight switch base due to tolerances from the factory, which is
also normal and twisting the switch slightly will aide with this; call us if you still have trouble with this switch.
slightly to accept the pods when they’re screwed in place. This was done to maximize mounting diameter and depth in each pod.
Also, ‘97-’00 models may have the driver side pod contact the headlight switch base due to tolerances from the factory, which is
also normal and twisting the switch slightly will aide with this; call us if you still have trouble with this switch.
* Color copies can be printed at
www.selectincrements.com
for better clarity, if necessary.
TJ DASH-PODS INSTALLATION
Screw speakers to pods with
the included #10 X 3/8” screws
the included #10 X 3/8” screws
Remove the speaker covers from
your TJ’s dash with a Phillips
screwdriver, 2 screws per side.
your TJ’s dash with a Phillips
screwdriver, 2 screws per side.
Remo e the speaker co ers from
Remove your current dash speakers with a Phillips
screwdriver, 4 screws per side. (You will reuse
these screws for the pods, so keep them aside).
Unplug the speakers from the factory plugs.
screwdriver, 4 screws per side. (You will reuse
these screws for the pods, so keep them aside).
Unplug the speakers from the factory plugs.
Remove foam pieces if
your TJ has them.
your TJ has them.
R
t d
1
2
3
Plug your DASH-PODS into
your existing factory wire
harness and reuse the mounting
plate screws that held your old
speakers in place to mount your
DASH-PODS. (It is normal to
have the backs of the pods hit
and flex the heater ducts in some
instances.) Replace the speaker
covers and you’re done!
your existing factory wire
harness and reuse the mounting
plate screws that held your old
speakers in place to mount your
DASH-PODS. (It is normal to
have the backs of the pods hit
and flex the heater ducts in some
instances.) Replace the speaker
covers and you’re done!
vers and you re done!
www.selectincrements.com
Email:
admin@selectincrements.com
Phone: 610-345-9044
Gently pull excess wire from pods
Screw speakers to pods with
4
7
8
9
Connect spade terminals to
speakers .
speakers .
5
Gently push
speaker
spade
terminals
inward
toward the
magnet if
needed for
wall
clearance.
speaker
spade
terminals
inward
toward the
magnet if
needed for
wall
clearance.
Before you screw the speakers
to the pods…
You may need to cut top inner
corners of speaker frames
to get clearance around
the metal bracing of the
dash. Only the corners shown
here may need to be cut, and
possibly just the Driver Side Pod.
to the pods…
You may need to cut top inner
corners of speaker frames
to get clearance around
the metal bracing of the
dash. Only the corners shown
here may need to be cut, and
possibly just the Driver Side Pod.
Passenger Side
Driver Side
6
(only if using 4x6 speakers)
10
OR
11
12
(Generally ‘97-’00)
If you have these
brackets, turn page
over. If not,
continue to #13.
13