Bazooka MBTA8250D Benutzeranleitung
15
MARINE TUBE SPECIFICA
TIONS
MBT80
14
MBT
10
14
MBT
A8
10
0
MBT
A1
01
00
MBT
A8200
MBT
A1
0200
Woofer Size
8
10
8
10
8
10
Voice Coil Size
1.5
high power
. /high temp.
1.5
high power
. /high temp.
1.5
high power
/high temp
1.5
high power
. /high temp.
1.5
h
igh p
ower
. /h
igh tem
p.
1.5
high p
ower
. /h
igh tem
p.
Magnet Size
28 oz.
28 oz.
15 oz.
28 oz.
28 oz.
28 oz.
Fre
qu
en
cy
res
po
nse
*
39-1
500 hz.
39-1000 hz.
39-85 hz.
39-85 hz.
39-250 hz.
39-250 hz.
Efficiency**
102 dB*
104 dB*
105 dB*
107 dB*
102 dB*
104 dB*
Power Handling
6-150 watts/channel
6-200 watts/channel
100 watts
100 watts
200 watts
200 watts
Dimensions
18 x 8.5 x 10
20.75 x 10.3 x 12.2
18.125x8.5x10
20.875x1
0.3x1
2.2
18.325" x 8.5" x 10"
21
.1"
x 10.3" x 12.2"
Weight
15.5 lbs.
23 lbs.
14 lbs.
24 lbs.
20 lbs.
25 lbs.
Impedance
4 ohms
4 ohms
2 ohms DVC
2 ohms DVC
4 ohms
4 ohms
* The built in crossover limits the frequency response of the Amplified Bazooka. ** The ef
ficiency levels of all Bazooka subwoofer speaker systems are measured in the typical environment: In the low bass regi
on with one watt of power
.
ENGLISH
16
AMPLIFIED MODELS:
(BTA6100, BTA8100, BTA10100, BTA6200, BTA8200, BTA10100,
MBTA8100, MBTA10100, MBTA8200, MBTA10200)
DO NOT substitute the fuse included with the Amplified Bazooka
subwoofer with anything other than the SAME fast blow current
rated fuse. Substitution or deletion will void the product's warranty
and may cause damage to your car or the amplifier.
SHOULD I USE HIGH OR LOW LEVEL INPUTS?
If the source unit has only speaker outputs, use the high-level inputs
of the Amplified Bazooka subwoofer. If the source unit has both high
and low level outputs, we recommend using the high level inputs
over the low level inputs, due to the configuration of the Amplified
Bazooka subwoofer's balanced input circuit. Not all head units, even
those that promise high output voltage in their marketing materials,
indeed have high-voltage RCA outputs. Because of this, Bazooka
Mobile Audio recommends using the speaker level inputs when in
doubtthey will always provide sufficient drive level to the amplifier.
PLEASE NOTE THAT THE WIRING IN A FACTORY STEREO MAY NOT BE
ELECTRICALLY IN PHASE EVEN WHEN YOU HAVE MADE THE PROPER
CONNECTIONS.
Take the time after you make your wire connections to run through
the quick phase check procedure in the AM I IN PHASE? section at
the end of this manual, and NEVER USE BOTH high and low-level
inputs at the same time!
INPUT SIGNAL CONNECTIONS
High-Level Inputs:
If the source unit has both front and rear speaker outputs, use
only one set of speaker outputs for the high-level input of the
Amplified Bazooka. Connect the GREEN wire from the 14-pin
Molex plug of the Amplified Bazooka subwoofer to the source
units left (+) positive speaker output. Connect the GREEN W/BLACK
stripe wire of the plug to the source units left (-) negative speaker
output. Connect the GRAY wire of the plug to the source units
right (+) positive speaker output. Connect the GRAY W/BLACK
stripe wire of the plug to the source units right (-) negative speaker
output. When using high-level inputs, take the time after you
make all wiring connections to run through the AM I IN PHASE
ENGLISH