Polk Audio Omni SB1 Plus Benutzeranleitung
1.
www.polkaudio.com
5
3. Press and release “Volume Up” button on the SB1’s
included remote.
4. Hold your TV’s remote 6" - 1' from the sound bar.
5. Press the “Volume Up” button on your TV’s IR remote
control once.
6. LEARN LEDs 3, 5, 7, 9, 11 turn solid; the command
has been learned. Two chimes confirm the command has
been learned.
been learned.
Repeat steps 1-6 to program “Volume Down”( – ), Source, Mute
and Power buttons.
and Power buttons.
Important note to save your tv’s ir remote commands:
After you’ve programmed all of the commands on your TV’s
remote control, press and hold the “Source/Learn” button for 5
seconds. This saves all of the commands.
After you’ve programmed all of the commands on your TV’s
remote control, press and hold the “Source/Learn” button for 5
seconds. This saves all of the commands.
Note: If your bar fails to learn certain IR remote codes, the
power LED will blink red three times. Try erasing any previously
programmed codes (see below) and carefully repeat steps
1-6 above.
power LED will blink red three times. Try erasing any previously
programmed codes (see below) and carefully repeat steps
1-6 above.
Code Erasing Procedure:
If you have programmed your Sound bar to respond to a remote
control and you no longer want it to do so, erase the codes by
pressing the “Source/Learn” button for 10 seconds. Previously
learned codes have been successfully erased when the POWER
LED flashes green ten times.
If you have programmed your Sound bar to respond to a remote
control and you no longer want it to do so, erase the codes by
pressing the “Source/Learn” button for 10 seconds. Previously
learned codes have been successfully erased when the POWER
LED flashes green ten times.
Note: This procedure removes ALL of your bar’s remote control
programming. If you only need to change the programming for
some of the bar buttons, follow the six steps in the sequence
previously described to redo any previous programming.
The Sound bar will continue to respond to the provided credit
card remote control.
programming. If you only need to change the programming for
some of the bar buttons, follow the six steps in the sequence
previously described to redo any previous programming.
The Sound bar will continue to respond to the provided credit
card remote control.
Getting Started for Wireless Music
Your Home Network
In general, Wi-Fi is the wireless streaming of data over a network.
Here, Wi-Fi audio is the streaming of music throughout a home
network by connecting multiple speakers and/or devices together.
The controller for the Polk Omni Collection is the Polk Omni App,
which sends music information to each DTS Play-Fi enabled
speaker or device.
Here, Wi-Fi audio is the streaming of music throughout a home
network by connecting multiple speakers and/or devices together.
The controller for the Polk Omni Collection is the Polk Omni App,
which sends music information to each DTS Play-Fi enabled
speaker or device.
System Requirements
It all begins by building a wireless home network, preferably one
with a high-speed Internet connection. Here’s what you’ll need to
connect your SB1 Plus to your network:
with a high-speed Internet connection. Here’s what you’ll need to
connect your SB1 Plus to your network:
• A Wireless Network connected to the internet with an 802.11g
router or better*.
• An Android device with version 2.2 operating system or newer
OR an iOS device with version 6.0 operating system or newer.
• The password for your wireless network (if required).
*Router type is usually listed on the router, itself. Please call the Polk Preferred
Services @ 1-800-638-7276 for further questions related to router type
.
For The Best DTS Play-Fi Experience
To ensure your system is operating under the best environment
possible, here are a few additional tips:
To ensure your system is operating under the best environment
possible, here are a few additional tips:
• For the fastest streaming performance, especially when
connecting to multiple speakers simultaneously, an 802.11ac
router or better is recommended.
router or better is recommended.
• Ensure the DTS Play-Fi device is within wireless reach of your
router, or that the signal is not hindered by concrete, brick, or
other dense walls. The quality of your connection can be
observed in the Polk Omni App by the Wireless Strength icon.
other dense walls. The quality of your connection can be
observed in the Polk Omni App by the Wireless Strength icon.
Wi-Fi Setup
1. To ensure the easiest setup, place your SB1 Plus near your
internet-connected wireless router. Note, when setup is
complete, you can move your device anywhere you want to.
complete, you can move your device anywhere you want to.
2. Connect the included power cable to the SB1 Plus and a
power outlet. The device will power on automatically.
3. The white light on the back will blink quickly for about
20 seconds, after which it will begin to pulse slowly.
4. The slowly pulsing light means your device is ready to
connect to your Wi-Fi network.
Note: if the Wi-Fi LED is
not pulsing slowly, Press and hold the Wi-Fi setup button
(for 8 seconds), until you hear the second tone.
(for 8 seconds), until you hear the second tone.
5. Download the Polk Omni App from the Apple App Store
or Google Play Store.
6. Launch the app and follow the instructions.
Utility App
Note: to enable Wi-Fi Protected Setup (WPS) mode with
a WPS compatible router, press and hold the Wi-Fi button
on the SB1 Plus for 4 seconds or until the first beep. Now
push the WPS button on your wireless router. The SB1 Plus
will automatically connect to your network without the need
to enter your password.
a WPS compatible router, press and hold the Wi-Fi button
on the SB1 Plus for 4 seconds or until the first beep. Now
push the WPS button on your wireless router. The SB1 Plus
will automatically connect to your network without the need
to enter your password.